v1.5 October 26, 2022 INCOMM L510 Lamp Controller USER GUIDE TABLE OF CONTENT Overview .................................................................................................................................................................................................. 2 Dimensions ............................................................................................................................................................................................. 3 LED status indications.
v1.5 October 26, 2022 INCOMM L510 LAMP CONTROLLER USER GUIDE OVERVIEW The L510 provides dimming control of almost any floor or desk lamp. The dimmer plugs right into your lamp and wall socket. Dimming the lights with the L510 saves energy and provides elegant lighting and mood control when used in conjunction with Honeywell's Integrated Room Automation System. Typical application L510 provides wireless remote control of a table or floor lamp while participating in a lighting scene or mood.
v1.5 October 26, 2022 INCOMM L510 LAMP CONTROLLER USER GUIDE DIMENSIONS LED STATUS INDICATIONS Off: L510 is not powered. On for 1/2 second, Off for 1/2 second, and repeating: L510 is powered but has not received a “Central Status Broadcast” and does not think the room it is in is Online/connected with the Inncom server. On for 1 second, Off for 1 second, and repeating: L510 is powered and has seen a “Central Status Broadcast” and does think the room it is in is Online/connected with the Inncom server.
v1.5 October 26, 2022 INCOMM L510 LAMP CONTROLLER USER GUIDE L510 H3 AND H4 MODULAR PLUG CONNECTIONS H3 RJ12 6-pin socket – Pins 2,3,5 provide an S5-Bus connection from the L510. Accepts a 6P6C RJ12 modular plug. Pins 1,4,6 not used. A 250mm and 3000mm pre-built cable depicted above is available for order. 62-1345 = CABLE ASSY, 3 PIN 250MM, RJ12 TO S5BUS W, 62-1345.10 = CABLE ASSY, 3 PIN CABLE, 3000MM, S5, 3 Pin Connector to RJ12 Connector. Figure 2. L510 H3 RJ12 Socket Figure 3.
v1.5 October 26, 2022 INCOMM L510 LAMP CONTROLLER USER GUIDE BINDING AND CONFIGURING THE L510 F OR L510 T Configure the L510 with a unique device address and required functionality, and it contains a radio that requires being “bound” to a specific Room ID, PAN ID, and RF Channel. Use a laptop with the EngINN program installed with a connected PC503 USB commissioning device to perform this binding and configuration. You can also configure it with an E7, E528/E527.
v1.5 October 26, 2022 INCOMM L510 LAMP CONTROLLER USER GUIDE c. Upon seeing the L510 startup, ENGINN will show a green check symbol indicating the bind was successful. 4. With the L510 bound and assigned its Room ID, PAN ID, and RF Channel, push its configuration from EngINN. a. Click the Back to Summary button to return to the Device Summary screen. b. Click the Write Configurations button.
INCOMM L510 LAMP CONTROLLER USER GUIDE The thermostat will display “rid” when it has entered Service Parameter mode. 2. If not already done, set the required Room ID, PAN ID, and RF Channel into the e7/e7w. These values will be transferred to the L510 when you initiate the Bind. If this is already set, skip to Step 3. Set the Room ID: a. Press Mode when the rid is displayed.
v1.5 October 26, 2022 INCOMM L510 LAMP CONTROLLER USER GUIDE Set the RF Channel: a. Use the UP/DOWN arrow buttons to select RF. b. Press MODE c. Use the UP/DOWN arrow buttons to select the RF Channel value. d. Press FAN to store the value in memory. e. Press °F|°C to exit service mode. 3. With the required Room ID, PAN ID, and RF Channel entered into the thermostat, now Bind the L510.
v1.5 October 26, 2022 INCOMM L510 LAMP CONTROLLER USER GUIDE The thermostat display will show bnd, indicating it is waiting to see a reverse bind command from the L510. On the L510, press its Bind/Service button to make the L510 send a Bind Request. The thermostat will send a Bind Offer to the L510 containing the defined values when it sees this message.
v1.5 October 26, 2022 INCOMM L510 LAMP CONTROLLER USER GUIDE Set the RF Channel: a. Use the UP/DOWN arrow buttons to select rF. b. Press DISPLAY c. Use the UP/DOWN arrow buttons to select the RF Channel value. d. Press DISPLAY to store the value in memory. e. Press °F|°C to exit service mode. 3. With the required Room ID, PAN ID, and RF Channel entered into the thermostat, now Bind the L510.
v1.5 October 26, 2022 INCOMM L510 LAMP CONTROLLER USER GUIDE TROUBLESHOOTING Binding and configuring issues 1. You can't Bind the L510 from EngINN. The “Bind” button is disabled Possible Reasons: Configure EngINN to connect to WSCon instead of the PC503. Look in the lower right corner of EngINN. If you see “Server (WSCon), configure EngINN to connect to the WSCon program instead of the PC503. Click the “Server (WSCon)” item to open a Settings window. From there, set the EngINN Communication.
v1.5 October 26, 2022 INCOMM L510 LAMP CONTROLLER USER GUIDE Possible Reasons: • The PC503 USB commissioning device is not connected to a USB port on the PC being used to run EngINN. There is an issue with the USB cable used, or the USB driver the PC503 uses did not install correctly. Look at the bottom right of EngINN. Does it indicate “PC503-Channel XX – Connected” or “Disconnected”. If it indicates disconnected, verify the connection between PC503, USB cable, and the used PC.
