User Guide
Table Of Contents
- 1. Safety
- 2. Receipt of delivery
- 3. Technical data
- 4. Installation
- 5. Commissioning
- 6. Fault tracing
- 7. SmartVFD Compact Application Interface
- 8. Control panel
- 9. General purpose application parameters
- 9.1 Quick setup parameters (Virtual menu, shows when par. 13.1 = 1)
- 9.2 Motor settings (Control panel: Menu PAR -> P1)
- 9.3 Start/stop setup (Control panel: Menu PAR -> P2)
- 9.4 Frequency references (Control panel: Menu PAR -> P3)
- 9.5 Ramps and brakes setup (Control panel: Menu PAR -> P4)
- 9.6 Digital inputs (Control panel: Menu PAR -> P5)
- 9.7 Analogue inputs (Control panel: Menu PAR -> P6)
- 9.8 Digital and analogue outputs (Control panel: Menu PAR - > P7)
- 9.9 Protections (Control panel: Menu PAR -> P9)
- 9.10 Autorestart parameters (Control panel: Menu PAR -> P10 )
- 9.11 PI control parameters (Control panel: Menu PAR -> P12 )
- 9.12 Easy usage menu (Control panel: Menu PAR -> P0 )
- 9.13 System parameters
- 10. Parameter descriptions
- 10.1 Motor settings (Control panel: Menu PAR -> P1)
- 10.2 Start/Stop setup (Control panel: Menu PAR -> P2)
- 10.3 Frequency references (Control panel: Menu PAR -> P3)
- 10.4 Ramps & brakes setup (Control panel: Menu PAR -> P4)
- 10.5 Digital inputs (Control panel: Menu PAR -> P5)
- 10.6 Analoque inputs (Control panel: Menu PAR -> P6)
- 10.7 Digital and analoque outputs (Control panel: Menu PAR -> P7)
- 10.8 Motor thermal protection (parameters 9.7 - 9.10)
- 10.9 Autorestart parameters (Control panel: Menu PAR -> P10)
- 10.10 PI control parameters (Control panel: Menu PAR -> P12)
- 10.11 Easy usage menu (Control panel: Menu PAR -> P9)
- 10.12 Fieldbus parameters (Control panel: Menu PAR -> S2 )
34 Control Panel Honeywell
8
8. CONTROL PANEL
8.1 GENERAL
The SmartVFD Compact API Full and API Limited versions have similar control pan-
els. The panel is integrated to the drive consisting of corresponding application card
and an overlay on the drive cover with status display and button clarifications.
The Control panel consists of an LCD display with backlight and a keypad including
a navigation wheel, a green START button and a red STOP button (see Figure 8.1).
8.2 DISPLAY
The display includes 14-segment and 7-segment blocks, arrowheads and clear text
unit symbols. The arrowheads, when visible, indicate some information about the
drive, which is printed in clear text on the overlay (numbers 1…14 in the figure be-
low). The arrowheads are grouped in 3 groups with the following meanings and Eng-
lish overlay texts (see Figure 8.1):
Group 1 - 5; Drive status
1= Drive is ready to start (READY)
2= Drive is running (RUN)
3= Drive has stopped (STOP)
4= Alarm condition is active (ALARM)
5= Drive has stopped due to a fault (FAULT)
Group 6 - 10; Control selections
6= Motor is rotating forward (FWD)
7= Motor is rotating reverse (REV)
8= I/O terminal block is the selected control place (I/O)
9= Keypad is the selected control place (KEYPAD)
10= Fieldbus is the selected control place (BUS)
Group 11 - 14; Navigation main menu
11= Reference main menu (REF)
12= Monitoring main menu (MON)
13= Parameter main menu (PAR)
14= Fault history main menu (FLT)