8” Stainless Steel Dishwasher User Manual Read and save these instructions before use HDS18SS
CONTENTS 1 Important Safety Instructions 1.1 Proper installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1.2 Basic precautions before use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 2 Installation Introduction 3 Features of Your New Dishwasher 3.1 Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1 IMPORTANT SAFETY INSTRUCTION WARNING: For your safety, please follow the information in this manual to minimize the risk of fire, explosion, electric shock and to help prevent property damage or personal injury. 1.1 Proper Installation Please install your dishwasher properly by following the installation guide. • Water supply inlet temperature should be between 120°F and 149°F. • Dispose of discarded appliances and packing materials properly.
• Do not let children hit, sit or stand on door or racks of the dishwasher. • Under certain conditions, hydrogen gas may be produced in a hot water system that has not been used for two weeks or more. HYDROGEN GAS IS EXPLOSIVE. If the hot water system has not been used for such a period, before using the dishwasher, turn on all hot water faucets and let water flow for several minutes. This will release any accumulated hydrogen gas. Hydrogen gas is flammable.
2 INSTALLATION INTRODUCTION BEFORE YOU BEGIN Read these instructions completely and carefully. IMPORTANT Observe all governing codes and ordinances. NOTE TO INSTALLER Be sure to leave these instructions for the consumer’s and local inspector’s use. NOTE TO CONSUMER Keep these instructions with your Owner’s Manual for future reference. SKILL LEVEL Installation of this dishwasher requires basic mechanical and electrical skills. Proper installation is the responsibility of the installer.
3 FEATURES OF YOUR NEW DISHWASHER 3.
3.2 Filter System Your dishwasher has a multiple Filter System. In the System there are three mesh filters. It can separate soiled water and clean water in different chambers. The multiple filter system helps your dishwasher to get better performance with less water and less energy. 3.3 Smart Wash System Your dishwasher has Smart Wash System. When a partial load of lightly soiled dishes is placed in the unit, a wash cycle similar to a short wash will automatically be performed.
Getting Started 01 Load the dishwasher. (See Dish Preparation and Loading sections) 02 Add detergent. (See Filling the Detergent Dispenser) 03 Add rinse aid. (See Filling the Rinse Aid Dispenser) 04 Select desired CYCLE. (See Cycle Chart) 05 Select desired OPTIONS (See Control Panel). The indicator light above the pad will glow when selected. 06 Run the hot water faucet nearest the dishwasher until the water is hot, then turn it off. 07 To start, press Start/Cancel. (See Control Panel) Then close door.
4 OPERATING INSTRUCTIONS Control Panel Wash Cycle Selections Start/Cancel Delay Status Indicators Display Window Options 4.1 Start/Cancel Open the door to select the desired cycle and options, touch the Start/Cancel button and close the door within 4 seconds to start the cycle or begin the delay countdown. To cancel and reset the program during the cycle, open the door, and touch Start/ Cancel for 3 seconds. Close the door and dishwasher will start a 60 second drain. 4.
4.5 Status Indicators • Rinse Deterfent needs to be refilled. • Program end. • Water failure, faucet is not open. 4.6 Options HEATING DRY When the “Heating Dry” function is selected, the heater will work during the drying processs. The Heating Dry option is not available with “Rinse” cycles. SANITIZE When the”Sanitize”function is selected, the temperature of water will be maintained at 69°C(156.2°F) max. The max temperature may not be reached if the incoming water temperature is not correct.
4.9 Cycle Chart Program Cycle Description Water (L) Cycle Time (min) Heavy Wash Pre Wash Main Wash (60°C) Rinse(65°C) Rinse (with Sani 69°C) Drying 19.7 155 Normal Wash Pre Wash Main Wash (50-55°C) Rinse(58-60°C) Rinse (with Sani 69°C) Drying 9.5~18.5 105~135 ECO Pre Wash Main Wash (50-55°C) Rinse(58-60°C) Rinse (with Sani 69°C) Drying 15.5 105 Glass Pre Wash Main Wash (48-50°C) Rinse(50-55°C) Drying 15.5 95 Rapid Pre Wash Main Wash (48-50°C) Rinse(50-55°C) 12.
5 USER MAINTENANCE Keeping your dishwasher clean improves its performance, reduces unnecessary repairs, and lengthens its life. 5.1 Cleaning the Exterior It’s best to clean spills on the outside of your dishwasher as they occur. Use a soft, damp cloth on the control panel to gently wipe away spills and dust. Do not use benzene, wax, thinner, chlorine bleach, or alcohol. These materials may discolor the inner walls and cause stains.
02 Rotate the filter insert counterclockwise to unfasten and detach the filter insert. 03 Remove the fine filter. (flat rectangle) 04 Remove any dirt or other remains from the filters, and then rinse them under running water. 05 Reassemble the filters in the reverse order of the dissasembly, replace the filter insert, and rotate clockwise to the close arrow. CAUTION If the filter is not closed properly, its preformance will be decreased.
Cleaning the Nozzles If your dishwasher does not seem to be cleaning adequately or the nozzles seem clogged, you can clean each of the nozzles. When removing the nozzles, take care as they may break. Lower Nozzle 01 Check whether the nozzle holes are clogged by food particles. 02 If cleaning is needed, remove the nozzle by pulling it upwads. 03 Clean the nozzle, and then push it back into place. 04 Check whether the nozzle is engaged correctly by rotating it by hand.
6 TROUBLESHOOTING Before Calling for Service Problem Dishwasher won’t start Dishwasher beeps at the end of cycle Rinse Aid light on Dishwasher operates too long Dishes are not clean enough Dishes are not drying enough Possible Cause Door may not be closed properly Power supply or power line is not connected Delay Start option has been selected Child Lock activated Solution Shut the door completely, make sure it is latched Check and connect the power supply, refer to this manual to reset Deactivate th
Problem Spots and filming on dishes Etching Detergent left in dispenser cup Detergent dispenser will not shut Possible Cause Solution Water hardness is too high Improper loading of dishes Old or damp powder Rinse Aid is used Rinse Dispenser empty For extremely hard water, install a water softener Load the dishes again as indicated Use fresh Rinse Aid Add Rinse Aid to the Dispenser Using too much detergent The inlet water temperature exceeds 150°F Use less detergent if you have soft water etching Lo
Problem Possible Cause Noises Detergent cup opening/Drain pump sound A hard object has entered the wash module. When the object is ground up, the sound should stop This is normal If the noise persists after a complete cycle, call for service Water valve is turned off Door latch may not be properly sealed Check if the water valve is turned on Make sure the door is closed Dishwasher won’t fill Solution 6.
7 TECHNICAL INFORMATION Capacity 8 place settings Dimension 17.6” x 21.7” x 32.4” (W x D x H) Power Supply 120 volts, 60Hz Rated Power Usage Wash Motor 100W, Heater 700W Water Feed Pressure 5.8 ~ 145 psi (0.
If you want to return or replace the product, please contact the store where it was purchased (remember to bring the purchase invoice). If your product needs repair, please contact us via email or phone. BHRS Group, LLC 585 Prospect St. Lakewood, NJ 08701 Customer Service Tel: 1-888-604-0295 Customer Service Email: support@honeywellcoolingappliances.com Website: honeywellcoolingappliances.com ©2022 BHRS Group, LLC. All Rights Reserved.
