Portable Evaporative Air Cooler OWNER’S MANUAL 1 0.5 4 2 COOL M H L Read and save these instructions before use SWING POWER TIMER SPEED Model: CS10XE Voltage rating: 110 Volt AC, 60Hz Power rating: 100 Watts Made in China.
INDEX Read all instructions carefully before setting up and operating the unit, and please keep this instruction manual for future reference. This manual is designed to provide you with important information needed to setup, operate, maintain, and troubleshoot your cooler. Failure to follow these instructions may damage and/or impair its operation and void the warranty. SECTION 1. 2. 3. 4. 5. 6. 7. 8. 9. PAGE THANK YOU .....................................................................................
THANK YOU THANK YOU! Congratulations on your purchase of this versatile Honeywell Evaporative Air Cooler. For optimum cooling performance from your unit, fill the water tank with water & ice (if available) to increase its cooling power. Please read these instructions carefully.
USER TIPS COOL ~ EFFICIENT ~ NATURAL Evaporative air cooling is the natural way of cooling, similar to a breeze blowing across a lake. This breeze drops the temperature and has a relaxing cooling effect. The evaporative air cooler cools the air by means of the evaporation of water. When water evaporates into the air, the result is a mixture of air and water molecules. This chemical change requires heat which is taken from the water molecules, resulting in cooler air propelled from the unit.
USER TIPS The recommended maximum relative humidity level is 60% or less, which allows a noticeable temperature decrease. The temperature decrease will be greater in drier climates because higher evaporation occurs when the humidity is low. The evaporative air cooler should not be used in enclosed spaces. It must be kept level and there must be water in the water tank. The room should have doors and windows opened to allow free air flow.
SAFETY RULES READ AND SAVE THESE INSTRUCTIONS: When using electrical appliances, basic safety precautions should always be followed: • Your cooler runs on 110 Volt AC, 60 Hz current. Check the household voltage to ensure it matches the appliance' s rate specification. • Before operating the product remove it from its packaging and check it is in good condition. • DO NOToperate any product with a damaged cord or plug. We recommend not using an extension cord with this appliance.
SAFETY RULES • DO NOT attempt to repair or adjust any electrical or mechanical functions of the cooler, as this may void the warranty. • DO NOT cover the air inlet or outlet on the appliance as this may cause motor damage. • DO NOT insert or allow objects to enter any ventilation or exhaust opening as this may damage the product and could cause an electrical shock or fire. • DO NOT operate with the Honeycomb media removed as this will overload and damage the motor.
PARTS DESCRIPTION 7 1 0.
USE & OPERATION CONTROL PANEL 1 0.5 4 2 M H L SL COOL SWING POWER TIMER SPEED Icons on LED Cool M H L SL Low speed Medium speed High speed Sleep 8 Swing 0.
USE & OPERATION FUNCTION BUTTONS POWER Press the ' POWER'button to turn the unit on. To turn the unit off, press the button again. The cooler will start automatically at medium speed. After a few seconds the speed will switch to low. SPEED Press the ' SPEED' button repeatedly and the speed will change. The indicator light will show the selected speed. High Medium Low Sleep M H L SL When sleep is selected airflow will randomly vary between High, Medium and Low.
USE & OPERATION SWING Press the ' ' SWING' 'button. The indicator light will come on and the louvers will begin to move from right to left automatically. Manually adjust the horizontal louvers to change vertical airflow. UP-DOWN AIR FLOW To adjust the vertical direction of air flow, adjust the horizontal louvers located behind the front grill manually. COOL To begin cooling the desired area press the ' ' COOL’' button. The indicator light will come on and the water pump will operate.
USE & OPERATION LOW WATER ALARM FUNCTION The unit is equipped with a low water sensor. When water in the tank is below the minimum level, you will hear 10 beeps and the COOL LED indicator will flash continuously. At the same time the power to the pump inside the unit will be cut off to protect the life of the pump. To disengage the alarm function, turn off and unplug the unit from the power outlet, and fill the tank with water above the minimum level.
USE & OPERATION REMOTE CONTROL Power: Speed: Cool: Swing: Timer: On / Off Low / Medium / High Pump ON / OFF Controls the motion of the louvers Controls timer function for automatic shut off NOTE • • • • • • The remote control for your air cooler already has its battery installed The remote control requires a CR2032(1 x 3V) coin type or equivalent battery for replacement. Always point the remote control signal transmitter towards the unit when operating. Make sure that the signal path is not obstructed.
USE & OPERATION FILL WATER Open the Water Fill Tray located at the back of the unit. The water tank of the unit holds up to 10 Litres of water. Water level display window is located on the front of the unit. Refill the water tank when water level is low. Do not fill water above the Max water level mark. Check water level in the tank before running the ' ' COOL' 'function. Please be sure water in the tank is always above minimum water level mark. Running the unit with inadequate water may cause pump failure.
CLEANING & MAINTENANCE WARNING • Before cleaning the unit, switch it to the ''off''position and • • • remove the plug from the power socket. To clean the outside, use a damp cloth to remove dirt and dust. Never use corrosive elements or any chemicals to clean this product. When the product is not in use, store the unit in a dry place out of direct sunlight. CLEANING & DRAINING THE WATER TANK: • Turn the power “off” and disconnect the air cooler from the • • • • • power supply.
CLEANING & MAINTENANCE CLEANING THE FILTER AND HONEYCOMB • • • • • • • The appliance is supplied with carbon filter & honeycomb cooling media. Always keep the carbon filter clean. You can wash the carbon filter at least twice a year or whenever you feel necessary. The carbon filter and honeycomb media are located inside the back panel. Open the back panel by pulling out the back grill to clean or replace the carbon filter or honeycomb media.
TROUBLESHOOTING GUIDE PROBLEM POSSIBLE CAUSE SOLUTION No discharge of air Cord is not plugged in. Make sure power cord is plugged in and the supply switch in ON. Power is not on. Try to turn the unit ON by pressing buttons on control panel or remote control. Pump is not turned ON. Turn on COOL function from remote or control panel. Low or no water in tank, when COOL is selected. Refill water tank. Damaged Pump or Calcium deposits on blower. Contact service centre. New Unit.
TROUBLESHOOTING GUIDE PROBLEM POSSIBLE CAUSE SOLUTION The unit does not respond Remote control batteries. Check batteries, Replace if needed. Try to operate using the control panel. Damaged PCB Try with remote control. If the unit responds, PCB board fasteners may be loose. Contact service centre. If neither remote control nor control panel works, PCB board may be damaged. Contact service centre.
TECHNICAL SPECIFICATIONS MODEL NO. CS10XE 110V 60Hz 100 Watts 10 Litre Honeycomb 360(L) x 315(W) x 720(H) mm 8.
: © 2012 AirTek International Corporation Limited The Honeywell Trademark is used under license from Honeywell International Inc. Honeywell International Inc. makes no representation or warranties with respect to this product. Manufactured by AirTek International Corporation Limited.
