Installation Guide

ManualsBrandsHoneywell ManualsOtherHoneywell AQ25A44B Programmable Boiler Relay Control Panel

INSTALLATION JOB RECORD

AQ25A44B Programmable Boiler Relay Control Panel

System commissioning date: _________________________

Customer: _______________________________________

Building address: _________________________________

INSTRUCTIONS:

Fill in the details of the equipment connected to the control module and the zoning module:

A Low voltage control module wiring

B Low voltage zone thermostats

C Low voltage zone valves with end switches

D Line voltage Boiler pump, DHW pump and AUX output

E Review and set DIP switch settings - once DIP switches for the zoning module (AQ15740B) have been set, complete the “Installer

Settings” diagram by filling in the circles to indicate the DIP switch position set during installation

File this with other installation records for equipment used on this installation.

A Boiler Controller Module

D Boiler Pump, DHW, and AUX Device

B Zoning Thermostats

C Zoning Valves

Terminal # 9-10 13-14 17-18 19-20

Terminal ID Aux In DHW Boiler Aux Out

Function

Installer

defined

DHW

demand

Boiler

demand

Installer

defined

Equipment

Manufacturer

Model #

Serial #

Date Code

Notes

Terminal ID Boiler DHW AUX

Function

Boiler loop

control

DHW loop

control

Line voltage-rated

Aux device control

(installer-defined)

Equipment

Manufacturer

Model #

Power draw

(Amps)

Notes

Home

M27622A

Terminal # 5-6 7-8 9-10 11-12

Terminal ID TH1 TH2 TH3 TH4

Function Zone call for heat

Equipment

Manufacturer

Model #

Date Code

Notes

Terminal ID Zone 1 Zone 2 Zone 3 Zone 4

Function Zone control

Equipment Valve Valve Valve Valve

Manufacturer

Model #

Power draw

Notes

Zone 1

Zone 2 Zone 3

Zone 4

M27623A

E DIP switch

(See back for

settings)

This is a legacy product document

supported by Resideo. It is no

longer manufactured

Summary of content (4 pages)

PAGE 1
AQ25A44B Programmable Boiler Relay Control Panel System commissioning date: _________________________ This is a legacy product document supported by Resideo.
PAGE 2
E Zoning Module DIP Switch Settings DIP Number 1 The correct settings for each zone module are: 4 • • • • 8 Diagnostic First Zone (1-4) Module: 1 = ON position; 2, 3, and 4 = OFF position Second Zone (5-8) Module: 2 = ON position; 1, 3, and 4 = OFF position Third Zone (9-12) Module: 3 = ON position; 1, 2, and 4 = OFF position Fourth Zone (13-16) Module: 4 = ON position; 1, 2, and 3 = OFF position For each zone group, there can be only one DIP switch in the right-hand (ON) position.
PAGE 3
EQUIPMENT SETTINGS The Installer Menu is used to establish and modify the system’s equipment and option settings. These include equipment settings for boiler operation, DHW management, zoning, auxiliary input/output operation, and option settings such as pump/valve exercise, and freeze protection. Use Table 1 to record the equipment settings for this installation. To record the equipment and option settings: A Press the Home button to return to the Home Page display.
PAGE 4
Table 1. Installer Menu – Equipment Setup Sub-menu. (Continued) EQUIPMENT SETUP SUB-MENU Sub-Menu and Option Range Factory Default AUXILIARY I/O AUX.IN (optional) SETBACK / VACANCY / EM. SHUT / NONE SETBACK AUX.OUT (optional) BOILER / SETBACK / ZONE OP. / ALARM / AUX.IN / DHW IN / HEAT IN / HT DMND / COOL / NONE BOILER AUX.PUMP (optional) BOILER / GROUP / OCC / BYPASS / FAN / NONE / AUX.IN / DHW IN / HEAT IN / HT DMND BOILER CYCLES/HOUR 2/3/4/5/6 4 MIN.OFF TIME 2 to 10 (minutes) 5M C.W.S.