Home Security System User Manual
Table Of Contents
- ONYX®FirstVision™
- Fire Alarm System Limitations
- Installation Precautions
- FCC Warning
- Section 1 Introduction
- Section 2 FirstVision Installation Instructions
- Section 3 Enabling FirstVision to Monitor Your Building
- 3.1 Process Overview
- 3.2 Make Connections to FirstVision
- 3.3 Turn on Power to FirstVision
- 3.4 Set the FirstVision Clock and Time Zone
- 3.5 Establish Communication Between Your LAN and FirstVision
- 3.6 Establish Gateway Communication
- 3.7 Copy Your Exported Building Design to FirstVision
- 3.8 Display Your Building Design on FirstVision
- 3.9 Test Your Building Design on FirstVision
- 3.10 Touch Screen Calibration
- Section 4 Operating Basics of FirstVision
- 4.1 Normal Operation (No Events Being Reported)
- Figure 4.1 FirstVision Display Example: No Alarms
- Figure 4.2 FirstVision Display Example: Floor Number Button
- Figure 4.3 FirstVision Display Example: Building Information
- Figure 4.4 FirstVision Display Example: Zoomed Floor Plan
- Figure 4.5 FirstVision Display Example: Moving Through a Zoomed Floor Plan
- Figure 4.6 FirstVision Display Example: HAZMAT Information
- 4.2 Investigating Gateway Disconnection
- 4.3 Operation When a Fire Alarm is Received
- 4.4 Operation After a Fire Alarm Has Been Cleared
- 4.5 Accessing the Log File
- 4.1 Normal Operation (No Events Being Reported)
- Section 5 The Development of FirstVision
- 5.1 The Current Situation for a Firefighter
- 5.2 The Technology of FirstVision
- 5.3 Expected Firefighter Interaction with the FirstVision
- 5.3.1 Example Emergency Situations
- Figure 5.1 Fire Scene Scenario Floor Plan Information
- Figure 5.2 Fire Scene Scenario Roof Plan Information
- Figure 5.3 Fire Scene Scenario HAZMAT Information
- Figure 5.4 Fire Scene Scenario Building Information
- Figure 5.5 Example Building Site Plan Information
- Figure 5.6 Example HAZMAT Information
- Figure 5.7 Example Contact Information
- 5.3.1 Example Emergency Situations
- Index
15FIRSTVISION™ Installation and Operation Manual - P/N: 53034:Rev: A2 10/29/07
Section 3 Enabling FIRSTVISION to Monitor Your
Building
3.1 Process Overview
The procedures documented in the section should be performed after your building’s life safety
monitoring system has been customized to F
IRSTVISION using the ONYX® FIRSTVISION™
Configuration Tool (refer to ONYX® F
IRSTVISION™ Configuration Tool Programming Manual
for information).
Process Steps to Enable FIRSTVISION
Step 1. "Make Connections to FIRSTVISION".
Step 2. "Turn on Power to F
IRSTVISION".
Step 3. "Establish Communication Between Your LAN and F
IRSTVISION".
Step 4. "Establish Gateway Communication".
Step 5. "Copy Your Exported Building Design to F
IRSTVISION".
Step 6. "Test Your Building Design on F
IRSTVISION".
3.2 Make Connections to FIRSTVISION
All of the procedures in this section require you to operate FIRSTVISION like a personal computer.
Because of that operation usage scenario, you MUST connect an external keyboard and a mouse to
F
IRSTVISION.
3.2.1 What To Connect and How To Make the Connections
Step 1. Connect a keyboard and mouse to the either of these connectors.
• USB ports on the front of F
IRSTVISION LCD (recommended). A keyboard with a USB
port (for the mouse) is ideal for connecting to F
IRSTVISION (Figure 3.1).
• PS/2 connectors located on the bottom of the LCD (Figure 3.2).
.
Figure 3.1 FIRSTVISION USB Keyboard and Mouse Connections
NOTE: You must unlock the front door of FIRSTVISION to gain access to the USB ports.
NOTE: To gain access to the PS/2 connectors, you must remove the screws holding the LCD
closed and then you must swing the LCD out.