Install Instructions

ManualsBrandsHoneywell ManualsDampersDual Auxiliary Switch for CREVAL actuators

X-XX UL

INSTALLATION INSTRUCTIONS

43191680-1

Auxiliary Swi

tch

APPLICATION

The 43191680-102 Dual Auxiliary Switch provides two

independent, spdt switching functions. Switching points

are adjustable over the full length of the actuator stroke; for

example, the switch can be used to switch pumps at any

point or to provide remote indication of any specific stroke

position. These switches are used with valve actuators as

shown in Table 1. The switches are furnished factory wired

to the terminal block. Fig. 1 illustrates the parts furnished

with this switch and the wiring connections.

IMPORTANT

These switches are rated at 24 Vac maximum.

Table 1. Applicable Actuators for

43191680-102 Dual Auxiliary Switches.

Fig. 1. Auxiliary Switch Parts and Wiring.

INSTALLATION

When Installing this Product...

1 Read these instructions carefully. Failure to follow

them could result in the equipment not operating

properly.

2 Check the part numbers in the preceding section to

be sure that the product is suitable for your applica-

tion.

3 The installer must be a trained, experienced service

technician.

4 After completing installation, use these instructions

to check product operation.

CAUTION

Disconnect the power supply to the auxiliary

potentiometer and actuator before beginning

installation to prevent electrical shock or equipment

damage.

Mounting, Connecting, and Adjusting

1 Remove actuator cover.

2 For M6421A/M7421A Actuators with a 3/4 in. stroke,

skip this step and proceed to Step 3.

For M6421B/M7421B Actuators with a 1-1/2 in.

stroke, replace the gear on the switch assembly with

the larger gear furnished in the bag assembly. See

Fig. 2. Be sure that the gear is positioned as shown

by the points marked as a-a and that the actuator

shaft is fully extended to the lower stop. Then

proceed to Step 3.

Actuator Stroke

ML6421A 3/4 in.

ML6421B 1-1/2 in.

ML7421A 3/4 in.

ML7421B 1-1/2 in.

63-2523

C8398

331122

4 5 61 2 3

YELLOW

BLUE

RED

BLUE-WHITE

RED-WHITE

YELLOW-ORANGE

S1 S2

4 5 61 2 3

S1 S2

Summary of content (4 pages)

PAGE 1
43191680-102 Auxiliary Switch INSTALLATION INSTRUCTIONS APPLICATION INSTALLATION The 43191680-102 Dual Auxiliary Switch provides two independent, spdt switching functions. Switching points are adjustable over the full length of the actuator stroke; for example, the switch can be used to switch pumps at any point or to provide remote indication of any specific stroke position. These switches are used with valve actuators as shown in Table 1. The switches are furnished factory wired to the terminal block.
PAGE 2
S1 T T + 0 0 1 2 33 4 5 6 43191680-102 AUXILIARY SWITCH S2 M15002 Fig. 4. Securing auxiliary switch assembly. STOP ! 5 Secure terminal block and label with Phillips head screws. See Fig. 5. a a 1 2 33 4 5 6 Fig. 2. Replacing gear on the switch assembly for M6421B/M7421B applications only. S1 24V 24VY 1 2 R1W1B1 R W B 3 Install the auxiliary switch assembly. Make sure the two tabs on the bottom of the switch assembly slip snugly into the slots provided in the actuator base. See Fig. 3 .
PAGE 3
S1 Wiring T T + 0 0 1 2 33 4 5 43191680-102 AUXILIARY SWITCH Route field wiring in through the conduit opening in the bottom of the actuator, connect to the switch assembly terminal block according to the job drawings, and replace the actuator cover. See Fig. 1 for terminal identification S2 CAUTION Disconnect the power supply to the auxiliary switches and actuator before wiring to prevent electrical shock or equipment damage. All wiring must comply with local codes, regulations, and ordinances.
PAGE 4
3191680-102 AUXILIARY SWITCH Home and Building Control Honeywell Inc. Honeywell Plaza P.O. Box 524 Minneapolis, MN 55408-0524 63-2523 G.C. 1-97 Printed in U.S.