User's Guide
Table Of Contents
- VG1602-UG
- Voyager 1602g User’s Guide
- Table of Contents
- Getting Started
- Programming the Interface
- Introduction
- Keyboard Country Layout
- Keyboard Style
- Keyboard Conversion
- Control Character Output
- Keyboard Modifiers
- Programming an Interface for an Access Point
- Keyboard Wedge
- Laptop Direct Connect
- RS232 Serial Port
- RS485
- USB IBM SurePos
- USB PC or Macintosh Keyboard
- USB HID
- USB Serial
- Remote MasterMind™ for USB
- Gilbarco® Terminal Default Settings
- Honeywell Bioptic Aux Port Configuration
- Datalogic™ Magellan® Aux Port Configuration
- NCR Bioptic Aux Port Configuration
- Wincor Nixdorf Terminal Default Settings
- Wincor Nixdorf Beetle™ Terminal Default Settings
- Wincor Nixdorf RS232 Mode A
- RS232 Modifiers
- Scanner to Bioptic Communication
- Programming the VG1602 Corded Interface
- Wireless System Operation
- Bluetooth Settings
- Minimizing Bluetooth/ISM Band Network Activity
- Communication Between the Scanner and the Host
- Programming the Scanner and Host
- RF (Radio Frequency) Module Operation
- System Conditions
- About the Battery
- Beeper and LED Sequences and Meaning
- Reset Scanner
- Scanner Report
- Scanner Address
- Linked Modes
- Out-of-Range Alarm
- Scanner Idle Alarm
- Scanner Power Time-Out Timer
- Flexible Power Management
- Multiple Scanner Operation
- Scanner Name
- Application Work Groups
- Resetting the Factory Defaults: All Application Work Groups
- Resetting the Custom Defaults: All Application Work Groups
- Access Point Operations
- Access Point LED Sequences and Meaning
- Access Point Address
- Paging
- Batch Mode
- Host Acknowledgment
- Input/Output Settings
- Programmable Button
- Power Up Beeper
- Beep on BEL Character
- Trigger Click
- Good Read and Error Indicators
- Manual Trigger Modes
- Serial Trigger Mode
- Poor Quality Codes
- CodeGate®
- Mobile Phone Read Mode
- Character Activation Mode
- Character Deactivation Mode
- Illumination Lights
- Aimer Delay
- Aimer Mode
- Centering
- Preferred Symbology
- Output Sequence Overview
- Multiple Symbols
- No Read
- Video Reverse
- Working Orientation
- Data Editing
- Data Formatting
- Symbologies
- All Symbologies
- Message Length Description
- Codabar
- Code 39
- Interleaved 2 of 5
- NEC 2 of 5
- Code 93
- Straight 2 of 5 Industrial (three-bar start/stop)
- Straight 2 of 5 IATA (two-bar start/stop)
- Matrix 2 of 5
- Code 11
- Code 128
- GS1-128
- Telepen
- UPC-A
- UPC-A/EAN-13 with Extended Coupon Code
- Coupon GS1 DataBar Output
- UPC-E0
- UPC-E1
- EAN/JAN-13
- EAN/JAN-8
- MSI
- GS1 DataBar Omnidirectional
- GS1 DataBar Limited
- GS1 DataBar Expanded
- Trioptic Code
- Codablock A
- Codablock F
- Label Code
- PDF417
- MacroPDF417
- MicroPDF417
- GS1 Composite Codes
- GS1 Emulation
- TCIF Linked Code 39 (TLC39)
- QR Code
- Data Matrix
- MaxiCode
- Aztec Code
- Chinese Sensible (Han Xin) Code
- Postal Codes - 2D
- Postal Codes - Linear
- Utilities
- Serial Programming Commands
- Product Specifications
- Maintenance and Troubleshooting
- Voyager 1602g User’s Guide
- REG-1602-RS
3 - 13
Resetting the Factory Defaults: All Application Work Groups
The following bar code defaults all of the work groups to the factory default settings.
To see what the factory default settings are, refer to the table of Menu Commands, beginning on page 9-4. The standard prod-
uct default settings for each of the commands are indicated by an asterisk (*).
Note: Scanning this bar code also causes both the scanner and the host to perform a reset and become unlinked. You must
relink (pair) the scanner to the host. Refer to Bluetooth Settings, page 3-1 for additional information.
If your scanner is in multiple scanner mode, you will hear up to 30 seconds of beeping while all scanners are relinked to
the host and the settings are changed.
Resetting the Custom Defaults: All Application Work Groups
If you want the custom default settings restored to all of the work groups, scan the Custom Product Default Settings bar code
below. (If there are no custom defaults, it will reset the work groups to the factory defaults.) See Setting Custom Defaults on
page 1-6 for further information about custom defaults.
Note: Scanning this bar code also causes both the scanner and the host to perform a reset and become unlinked. You must
relink (pair) the scanner to the host. See Bluetooth Settings, page 3-1 for additional information.
If your scanner is in multiple scanner mode, you will hear up to 30 seconds of beeping while all scanners are relinked to
the host and the settings are changed.
Access Point Operations
The Voyager 1602g can pair with a Honeywell Access Point (AP01-010BT or AP01-100BT), which provides 2-way communica-
tion between the scanner and host.
Linking the Scanner to an Access Point
Turn on the host computer (laptop/desktop). Plug the interface cable into the Access Point
first and then into the appropriate port on the computer. The Page button lights up when the
connection to the host is made.
Factory Default Settings:
All Work Groups
PAPDFT&
Custom Default Settings:
All Work Groups
Page
Button
VG1602-UG C Released Honeywell proprietary & Confidential
The HEC and TEC codes identified in this watermark supersede any conflicting HEC or TEC codes displayed in the drawing.
Downloaded By: Shen, Scott - 16 June 2022 07:14:56 UTC HEC: EAR99 TEC: EAR99 GOV: ESO1.0