User's Guide
Table Of Contents
- VG1602-UG
- Voyager 1602g User’s Guide
- Table of Contents
- Getting Started
- Programming the Interface
- Introduction
- Keyboard Country Layout
- Keyboard Style
- Keyboard Conversion
- Control Character Output
- Keyboard Modifiers
- Programming an Interface for an Access Point
- Keyboard Wedge
- Laptop Direct Connect
- RS232 Serial Port
- RS485
- USB IBM SurePos
- USB PC or Macintosh Keyboard
- USB HID
- USB Serial
- Remote MasterMind™ for USB
- Gilbarco® Terminal Default Settings
- Honeywell Bioptic Aux Port Configuration
- Datalogic™ Magellan® Aux Port Configuration
- NCR Bioptic Aux Port Configuration
- Wincor Nixdorf Terminal Default Settings
- Wincor Nixdorf Beetle™ Terminal Default Settings
- Wincor Nixdorf RS232 Mode A
- RS232 Modifiers
- Scanner to Bioptic Communication
- Programming the VG1602 Corded Interface
- Wireless System Operation
- Bluetooth Settings
- Minimizing Bluetooth/ISM Band Network Activity
- Communication Between the Scanner and the Host
- Programming the Scanner and Host
- RF (Radio Frequency) Module Operation
- System Conditions
- About the Battery
- Beeper and LED Sequences and Meaning
- Reset Scanner
- Scanner Report
- Scanner Address
- Linked Modes
- Out-of-Range Alarm
- Scanner Idle Alarm
- Scanner Power Time-Out Timer
- Flexible Power Management
- Multiple Scanner Operation
- Scanner Name
- Application Work Groups
- Resetting the Factory Defaults: All Application Work Groups
- Resetting the Custom Defaults: All Application Work Groups
- Access Point Operations
- Access Point LED Sequences and Meaning
- Access Point Address
- Paging
- Batch Mode
- Host Acknowledgment
- Input/Output Settings
- Programmable Button
- Power Up Beeper
- Beep on BEL Character
- Trigger Click
- Good Read and Error Indicators
- Manual Trigger Modes
- Serial Trigger Mode
- Poor Quality Codes
- CodeGate®
- Mobile Phone Read Mode
- Character Activation Mode
- Character Deactivation Mode
- Illumination Lights
- Aimer Delay
- Aimer Mode
- Centering
- Preferred Symbology
- Output Sequence Overview
- Multiple Symbols
- No Read
- Video Reverse
- Working Orientation
- Data Editing
- Data Formatting
- Symbologies
- All Symbologies
- Message Length Description
- Codabar
- Code 39
- Interleaved 2 of 5
- NEC 2 of 5
- Code 93
- Straight 2 of 5 Industrial (three-bar start/stop)
- Straight 2 of 5 IATA (two-bar start/stop)
- Matrix 2 of 5
- Code 11
- Code 128
- GS1-128
- Telepen
- UPC-A
- UPC-A/EAN-13 with Extended Coupon Code
- Coupon GS1 DataBar Output
- UPC-E0
- UPC-E1
- EAN/JAN-13
- EAN/JAN-8
- MSI
- GS1 DataBar Omnidirectional
- GS1 DataBar Limited
- GS1 DataBar Expanded
- Trioptic Code
- Codablock A
- Codablock F
- Label Code
- PDF417
- MacroPDF417
- MicroPDF417
- GS1 Composite Codes
- GS1 Emulation
- TCIF Linked Code 39 (TLC39)
- QR Code
- Data Matrix
- MaxiCode
- Aztec Code
- Chinese Sensible (Han Xin) Code
- Postal Codes - 2D
- Postal Codes - Linear
- Utilities
- Serial Programming Commands
- Product Specifications
- Maintenance and Troubleshooting
- Voyager 1602g User’s Guide
- REG-1602-RS
2 - 22
Scanner to Bioptic Communication
The following Scanner to Bioptic Communication settings should only be used when connecting through an Access Point.
They are used to set up communication between Honeywell scanners and bioptic scanners.
Note: The scanner’s baud rate must be set to 38400 and the RS232 timeout must be set to 3000 in order to communicate
with a bioptic scanner. See "RS232 Modifiers" on page 2-18, and RS232 Timeout on page 2-21 for further
information.
Scanner-Bioptic Packet Mode
Packet Mode On must be scanned to set the scanner’s format so it is compatible with a bioptic scanner. Default =
Packet Mode Off.
Scanner-Bioptic ACK/NAK Mode
Bioptic ACK/NAK On must be scanned so the scanner will wait for an ACK or NAK from a bioptic scanner after each
packet is sent. The Scanner-Bioptic ACK/NAK Timeout (below) controls how long the scanner will wait for a response.
Default = Bioptic ACK/NAK Off.
Scanner-Bioptic ACK/NAK Timeout
This allows you to set the length (in milliseconds) for a timeout for a bioptic scanner’s ACK/NAK response. Scan the
bar code below, then set the timeout (from 1-30,000 milliseconds) by scanning digits from the inside back cover, then
scanning Save. Default = 5100.
* Packet Mode Off
Packet Mode On
* Bioptic ACK/NAK Off
Bioptic ACK/NAK On
ACK/NAK Timeout
VG1602-UG C Released Honeywell proprietary & Confidential
The HEC and TEC codes identified in this watermark supersede any conflicting HEC or TEC codes displayed in the drawing.
Downloaded By: Shen, Scott - 16 June 2022 07:14:56 UTC HEC: EAR99 TEC: EAR99 GOV: ESO1.0