User's Guide
Table Of Contents
- VG1602-UG
- Voyager 1602g User’s Guide
- Table of Contents
- Getting Started
- Programming the Interface
- Introduction
- Keyboard Country Layout
- Keyboard Style
- Keyboard Conversion
- Control Character Output
- Keyboard Modifiers
- Programming an Interface for an Access Point
- Keyboard Wedge
- Laptop Direct Connect
- RS232 Serial Port
- RS485
- USB IBM SurePos
- USB PC or Macintosh Keyboard
- USB HID
- USB Serial
- Remote MasterMind™ for USB
- Gilbarco® Terminal Default Settings
- Honeywell Bioptic Aux Port Configuration
- Datalogic™ Magellan® Aux Port Configuration
- NCR Bioptic Aux Port Configuration
- Wincor Nixdorf Terminal Default Settings
- Wincor Nixdorf Beetle™ Terminal Default Settings
- Wincor Nixdorf RS232 Mode A
- RS232 Modifiers
- Scanner to Bioptic Communication
- Programming the VG1602 Corded Interface
- Wireless System Operation
- Bluetooth Settings
- Minimizing Bluetooth/ISM Band Network Activity
- Communication Between the Scanner and the Host
- Programming the Scanner and Host
- RF (Radio Frequency) Module Operation
- System Conditions
- About the Battery
- Beeper and LED Sequences and Meaning
- Reset Scanner
- Scanner Report
- Scanner Address
- Linked Modes
- Out-of-Range Alarm
- Scanner Idle Alarm
- Scanner Power Time-Out Timer
- Flexible Power Management
- Multiple Scanner Operation
- Scanner Name
- Application Work Groups
- Resetting the Factory Defaults: All Application Work Groups
- Resetting the Custom Defaults: All Application Work Groups
- Access Point Operations
- Access Point LED Sequences and Meaning
- Access Point Address
- Paging
- Batch Mode
- Host Acknowledgment
- Input/Output Settings
- Programmable Button
- Power Up Beeper
- Beep on BEL Character
- Trigger Click
- Good Read and Error Indicators
- Manual Trigger Modes
- Serial Trigger Mode
- Poor Quality Codes
- CodeGate®
- Mobile Phone Read Mode
- Character Activation Mode
- Character Deactivation Mode
- Illumination Lights
- Aimer Delay
- Aimer Mode
- Centering
- Preferred Symbology
- Output Sequence Overview
- Multiple Symbols
- No Read
- Video Reverse
- Working Orientation
- Data Editing
- Data Formatting
- Symbologies
- All Symbologies
- Message Length Description
- Codabar
- Code 39
- Interleaved 2 of 5
- NEC 2 of 5
- Code 93
- Straight 2 of 5 Industrial (three-bar start/stop)
- Straight 2 of 5 IATA (two-bar start/stop)
- Matrix 2 of 5
- Code 11
- Code 128
- GS1-128
- Telepen
- UPC-A
- UPC-A/EAN-13 with Extended Coupon Code
- Coupon GS1 DataBar Output
- UPC-E0
- UPC-E1
- EAN/JAN-13
- EAN/JAN-8
- MSI
- GS1 DataBar Omnidirectional
- GS1 DataBar Limited
- GS1 DataBar Expanded
- Trioptic Code
- Codablock A
- Codablock F
- Label Code
- PDF417
- MacroPDF417
- MicroPDF417
- GS1 Composite Codes
- GS1 Emulation
- TCIF Linked Code 39 (TLC39)
- QR Code
- Data Matrix
- MaxiCode
- Aztec Code
- Chinese Sensible (Han Xin) Code
- Postal Codes - 2D
- Postal Codes - Linear
- Utilities
- Serial Programming Commands
- Product Specifications
- Maintenance and Troubleshooting
- Voyager 1602g User’s Guide
- REG-1602-RS
9 - 13
Output Sequence Editor Enter Sequence SEQBLK 4-17
Default Sequence SEQDFT 4-17
Partial Sequence Transmit Partial Sequence SEQTTS1 4-17
*Discard Partial Sequence SEQTTS0 4-17
Require Output Sequence Required SEQ_EN2 4-18
On/Not Required SEQ_EN1 4-18
*Off SEQ_EN0 4-18
Multiple Symbols On SHOTGN1 4-18
*Off SHOTGN0 4-18
No Read On SHWNRD1 4-18
*Off SHWNRD0 4-18
Video Reverse Video Reverse Only VIDREV1 4-19
Video Reverse and Standard Bar
Codes
VIDREV2 4-19
*Video Reverse Off VIDREV0 4-19
Working Orientation *Upright ROTATN0 4-20
Vertical, Bottom to Top (Rotate
CCW 90°)
ROTATN1 4-20
Upside Down ROTATN2 4-20
Vertical, Top to Bottom (Rotate CW
90°)
ROTATN3 4-20
Prefix/Suffix Selections
Add CR Suffix to All Symbologies VSUFCR 5-2
Prefix Add Prefix PREBK2## 5-2
Clear One Prefix PRECL2 5-2
Clear All Prefixes PRECA2 5-2
Suffix Add Suffix SUFBK2## 5-2
Clear One Suffix SUFCL2 5-2
Clear All Suffixes SUFCA2 5-2
Function Code Transmit *Enable RMVFNC0 5-3
Disable RMVFNC1 5-3
Intercharacter Delay Range 0 - 1000 (5ms increments) DLYCHR## 5-3
User Specified
Intercharacter Delay
Delay Length
0 - 1000 (5ms increments)
DLYCRX## 5-4
Character to Trigger Delay DLY_XX## 5-4
Interfunction Delay Range 0 - 1000 (5ms increments) DLYFNC## 5-4
Intermessage Delay Range 0 - 1000 (5ms increments) DLYMSG## 5-4
Data Formatter Selections
Data Format Editor *Default Data Format (None) DFMDF3 6-1
Enter Data Format DFMBK3## 6-2
Clear One Data Format DFMCL3 6-2
Clear All Data Formats DFMCA3 6-2
Selection
Setting
* Indicates default
Serial Command
# Indicates a numeric entry
Page
VG1602-UG C Released Honeywell proprietary & Confidential
The HEC and TEC codes identified in this watermark supersede any conflicting HEC or TEC codes displayed in the drawing.
Downloaded By: Shen, Scott - 16 June 2022 07:14:56 UTC HEC: EAR99 TEC: EAR99 GOV: ESO1.0