Quick Start Guide

ManualsBrandsHoneywell Home ManualsAir CleanersMedia Air Cleaner 20" x 25", MERV 13 (2000 cfm)

Tools needed to install

Enhanced Air Cleaner

Standard screwdriver

Phillips screwdriver

Metal cutter

Drill

Duct Sealant

Mounting the Media Air Cleaner

STEP ONE: Review the Installation Plan

Temporarily place the cabinet on the ﬂoor, oriented as it will be when installed. Insert and remove the cartridge to make sure the

plan allows adequate clearance for easy removal and replacement of the cartridge.

STEP TWO: Fasten the Cabinet to the Furnace

a. Align the cabinet with the return air opening.

b. Place blocks under the cabinet, as necessary, to make sure the unit sits securely.

c. Create an opening in the furnace to match the cabinet opening.

d. Attach the cabinet securely to the furnace. Attach the unit directly or ﬁt a starting collar in the furnace opening. Either drill

holes and fasten with sheetmetal screws or rivets, or use slip joints. If you are drilling holes, use a locking pliers to help hold

the unit in place during drilling.

STEP THREE: Install Turning Vanes

Install turning vanes to help distribute air equally over the full surface of the upstream side of the media. Install them whenever

an abrupt 90 degree elbow is installed directly against the media air cleaner cabinet.

STEP FOUR: Fasten Cabinet to Ductwork

Fasten side of cabinet to the ductwork using sheet-metal screws, rivets, or slip joints, as appropriate.

STEP FIVE: Connect Ductwork

a. Connect the vertical duct section to the elbow. If the vertical drop of the duct is less than 7 in. (178 mm) from the side of the

furnace, shorten the horizontal trunk or attach an offset ﬁtting to the elbow.

b. When ductwork is properly aligned, connect the vertical duct to the horizontal trunk.

STEP SIX: Seal Joints

Seal all joints in the return air system between the media air ﬁlter and the furnace to prevent dust from entering the clean

airstream.

Application Considerations

Air Conditioning: Mount the media air cleaner up-

stream of the evaporator coil in a cooling system.

Humidiﬁers: The media air cleaner is compatible

with humidiﬁers. Avoid applications where water mist

will reach the media.

UV Lights: Germicidal UV lights can cause degrada-

tion of the media ﬁlter. The UV light should be located

out of line of sight or a minimum of 3 feet from the

ﬁlter.

Choosing a Mounting Position

The Media Air Cleaner mounts in any position within

the return air duct, usually next to the furnace blower

compartment, but the arrow on the cartridge must

point in the same direction as the airﬂow.

NOTE: The media air cleaner cabinet is sturdy

enough to easily support the weight of the

furnace and evaporator coil.

Important Installation Requirements

Personal Safety

• Wear safety glasses while installing the unit.

• Do not cut into any air conditioning or

electrical line.

• Follow professional safety standards and

all local codes for plumbing, electrical, and

mechanical considerations.

Failure to comply with these requirements

will result in voided warranty, improper

installation, and service callbacks.

M939C

Highboy furnace with side

installation.

STEP SEVEN: Install Filter Cartridge

Slide the ﬁlter cartridge into the cabinet, making sure the arrow on the cartridge

points in the direction of air ﬂow. Replace access door. Insert the tab on the bottom

of the door into the slot in the cabinet. Swing the door closed and press it into place.

Media Air Cleaners

QUICK START GUIDE

33-00240EF-03

Summary of content (4 pages)

PAGE 1
Media Air Cleaners QUICK START GUIDE Important Installation Requirements Application Considerations Air Conditioning: Mount the media air cleaner upstream of the evaporator coil in a cooling system. Failure to comply with these requirements will result in voided warranty, improper installation, and service callbacks. Humidifiers: The media air cleaner is compatible with humidifiers. Avoid applications where water mist will reach the media.
PAGE 2
F100 Specifications F200 Specifications MERV Rating*: MERV 11 Static Pressure Drop: 0.23 (in. w.c.) at 500 FPM Efficiency Definition*: Small Particles: E1 = 0.3 to 1.0 microns = 32% Medium Particles: E2 = 1.0 to 3.0 microns = 72% Large Particles: E3 = 3.0 to 10.0 microns = 96% MERV Rating*: MERV 13 Static Pressure Drop: 0.3 (in. w.c.) at 500 FPM Efficiency Definition*: Small Particles: E1 = 0.3 to 1.0 microns = 63% Medium Particles: E2 = 1.0 to 3.0 microns = 91% Large Particles: E3 = 3.0 to 10.
PAGE 3
Épurateurs d’air à fibres GUIDE DE DÉMARRAGE RAPIDE Exigences d’installation importantes Considérations relatives à l’application Climatisation: Monter l’épurateur d’air à fibres en amont du serpentin d’évaporation du système de refroidissement. Humidificateurs: L’épurateur d’air à fibres est compatible avec les humidificateurs. Éviter les applications dans lesquelles de la brume d’eau peut atteindre le filtre. Lampes UV: Les lampes UV germicides peuvent endommager le filtre à fibres.
PAGE 4
Caractéristiques du F100 Caractéristiques du F200 Valeur MERV* : MERV 11 Chute de pression statique : 0,23 (PO C.E.) @ 2,54 m/s Cotes d’efficacité* : Petites particules : E1 = 0,3 à 1,0 microns = 32% Particules moyennes : E2 = 1,0 à 3,0 microns = 72% Grosses particules : E3 = 3,0 à 10,0 microns = 96% Valeur MERV* : MERV 13 Chute de pression statique : 0,3 (PO C.E.