Instructions
Table Of Contents
- Xenon™ XP 195X Series User Guide
- Disclaimer, Copyright, Trademarks & Patents
- Customer Support
- Table of Contents
- Get Started
- Program the Interface
- Introduction
- Program the Interface - Plug and Play
- Keyboard Wedge
- Laptop Direct Connect
- RS232 Serial Port
- RS485
- USB IBM SurePos
- USB PC or Macintosh Keyboard
- USB HID
- USB Serial
- Verifone® Ruby Terminal
- Gilbarco® Terminal
- Honeywell Bioptic Aux Port
- Datalogic™ Magellan® Aux Port
- Wincor Nixdorf Terminal
- Wincor Nixdorf Beetle™ Terminal
- Wincor Nixdorf RS232 Mode A
- Keyboard Country Layout
- Keyboard Wedge Modifiers
- Keyboard Style
- Keyboard Conversion
- Control Character Output
- Keyboard Modifiers
- RS232 Modifiers
- Scanner to Bioptic Communication
- Cordless System Operation
- How the Cordless Charge Base/Access Point Works
- Link the Scanner to a Charge Base
- Link the Scanner to an Access Point
- Replace a Linked Scanner
- Communication Between the Cordless System and the Host
- Program the Scanner and Base or Access Point
- RF (Radio Frequency) Module Operation
- System Conditions
- Page Button
- Page Button and Presentation Modes
- Charge Information
- Battery Information for the Xenon XP 1952g/1952h
- Instant Charge Pack Information for the Xenon XP 1952g-BF/Xenon XP 1952h-BF
- Beeper and LED Sequences and Meaning
- Low Power Alerts
- Reset Scanner
- Scan While in Base Cradle
- Base Charge Modes
- Page
- Error Indicators
- Scanner Report
- Scanner Address
- Base or Access Point Address
- Scanner Modes
- Unlink the Scanner
- Out-of-Range Alarm
- Scanner Power Time-Out Timer
- Flexible Power Management
- Batch Mode
- Multiple Scanner Operation
- Scanner Name
- Application Work Groups
- Reset the Factory Defaults: All Application Work Groups
- Reset the Custom Defaults: All Application Work Groups
- Use the Scanner with Bluetooth Devices
- Minimize Bluetooth/ISM Band Network Activity
- Host Acknowledgment
- Input/Output Settings
- Power Up Beeper
- Beep on BEL Character
- Trigger Click
- Good Read and Error Indicators
- Trigger Modes
- Presentation Mode
- In-Stand Sensor Mode
- Poor Quality Codes
- CodeGate™
- Streaming Presentation™ Mode
- Hands Free Time-Out
- Reread Delay
- Character Activation
- Character Deactivation
- Illumination Lights
- Aimer Delay
- Aimer Mode
- Centering
- Preferred Symbology
- Output Sequence Overview
- Output Sequence Editor Commands
- Enter Output Sequence
- Multiple Symbols
- No Read
- Video Reverse
- Working Orientation
- Healthcare Settings
- Data Edit
- Data Format
- Symbologies
- All Symbologies
- Message Length Description
- Codabar
- Code 39
- Interleaved 2 of 5
- NEC 2 of 5
- Code 93
- Straight 2 of 5 Industrial (three-bar start/stop)
- Straight 2 of 5 IATA (two-bar start/stop)
- Matrix 2 of 5
- Code 11
- Code 128
- GS1-128
- Telepen
- UPC-A
- UPC-A/EAN-13 with Extended Coupon Code
- Coupon GS1 DataBar Output
- UPC-E0
- UPC-E1
- EAN/JAN-13
- EAN/JAN-8
- MSI
- GS1 DataBar Omnidirectional
- GS1 DataBar Limited
- GS1 DataBar Expanded
- Trioptic Code
- Codablock A
- Codablock F
- Label Code
- PDF417
- MacroPDF417
- MicroPDF417
- GS1 Composite Codes
- GS1 Emulation
- TCIF Linked Code 39 (TLC39)
- QR Code
- DotCode
- Digimarc Barcode™
- Data Matrix
- MaxiCode
- Aztec Code
- Chinese Sensible (Han Xin) Code
- Postal Codes - 2D
- Postal Codes - Linear
- Imaging Commands
- Single-Use Basis
- Command Syntax
- Image Snap - IMGSNP
- Image Ship - IMGSHP
- IMGSHP Modifiers
- A - Infinity Filter
- C - Compensation
- D - Pixel Depth
- E - Edge Sharpen
- F - File Format
- H - Histogram Stretch
- I - Invert Image
- IF- Noise Reduction
- IR - Image Rotate
- J - JPEG Image Quality
- K - Gamma Correction
- L, R, T, B, M - Image Cropping
- P - Protocol
- S - Pixel Ship
- U - Document Image Filter
- V - Blur Image
- W - Histogram Ship
- Image Size Compatibility
- IMGSHP Modifiers
- Intelligent Signature Capture - IMGBOX
- RF Default Imaging Device
- Utilities
- Serial Programming Commands
- Product Specifications
- Xenon XP 1950g/1950h Corded Scanner Product Specifications
- Xenon XP 1952g/1952h Cordless Scanner Product Specifications
- Xenon XP 1952g-BF/1952h-BF Scanner Product Specifications
- CCB01-010BT/CCB01-010BT-BF Charge Base Product Specifications
- CCB-H-010BT/CCB-H-010BT-BF Charge Base Product Specifications
- Depth of Field Charts
- Standard Connector Pinouts
- Required Safety Labels
- Maintenance and Troubleshooting
- Reference Charts
- XEN195X-EN-UG-01 Rev E, 7/20
CHAPTER
11
Xenon XP User Guide 241
SERIAL PROGRAMMING
COMMANDS
The serial programming commands can be used in place of the programming bar-
codes. Both the serial commands and the programming barcodes will program the
scanner. For complete descriptions and examples of each serial programming
command, refer to the corresponding programming barcode in this manual.
The device must be set to an RS232 interface (see page 16). The following com-
mands can be sent via a PC COM port using terminal emulation software.
Conventions
The following conventions are used for menu and query command descriptions:
parameter A label representing the actual value you should send as part of a
command.
[option] An optional part of a command.
{Data} Alternatives in a command.
bold Names of menus, menu commands, buttons, dialog boxes, and win-
dows that appear on the screen.
Menu Command Syntax
Menu commands have the following syntax (spaces have been used for clarity
only):
Prefix [:Name:] Tag SubTag {Data} [, SubTag {Data}] [; Tag SubTag {Data}] […] Storage
Prefix Three ASCII characters: SYN M CR (ASCII 22,77,13).
:Name: This command is only used with cordless devices. It is used to specify
whether you’re communicating with the base or the scanner. To send
information to the scanner (with the base connected to host), use
:Xenon: The default factory setting for a Xenon XP scanner is Xenon