® Owner’s Manual Rotary Mower HRB216TDA ® EM3 POM53249-C 31VE2752 00X31-VE2-7520 Printed on Recycled Paper IPC 10000.2002.04 PRINTED IN U.S.A. © 1997, 2000–2002 American Honda Motor Co., Inc.
QUICK REFERENCE INFORMATION B WARNING: B The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Fuel type Unleaded gasoline with a pum p octane of 86 or higher Engine Oil Spark Plug capacity 0.29 U.S. gallon (1.1 liter) type SAE 10W-30 capacity 0.58 U.S. quart (0.
INTRODUCTION Congratulations on your selection of a Honda lawn mower! We are certain you will be pleased with your purchase of one of the finest lawn mowers on the market. We want to help you get the best results from your new mower and to operate it safely. This manual contains the information on how to do that; please read it carefully. As you read this manual, you will find information preceded by a NOTICE symbol.
INTRODUCTION A FEW WORDS ABOUT SAFETY Your safety, and the safety of others, is very important. And using this lawn mower safely is an important responsibility. To help you make informed decisions about safety, we have provided operating procedures and other information on labels and in this manual. This information alerts you to potential hazards that could hurt you or others. Of course, it is not practical or possible to warn you about all the hazards associated with operating or maintaining a lawn mower.
CONTENTS LAWNMOWER SAFETY ............................................................................4 IMPORTANT SAFETY INFORMATION ..................................................4 SAFETY LABEL LOCATIONS.................................................................6 CONTROLS & FEATURES ........................................................................7 COMPONENT & CONTROL LOCATIONS..............................................7 BEFORE OPERATION ..................................................
LAWNMOWER SAFETY IMPORTANT SAFETY INFORMATION Most accidents with walk-behind mowers can be prevented if you follow all instructions in this manual and on the mower. The most common hazards, according to accident statistics, are discussed below, along with the best way to protect yourself and others. Avoid Rotating Blades Rotating blades can cause serious cuts and even amputate fingers, hands, toes, or feet. Keep away from the mower deck whenever the engine is running.
LAWNMOWER SAFETY Operating Near Roads Always watch for vehicle traffic when operating the mower near roads and driveways. Never operate the mower on public roads. Operator Responsibility Know how to stop the mower quickly in case of emergency. Understand the use of all mower controls. Never permit anyone to operate the mower without proper instruction. Do not let children operate the mower.
LAWNMOWER SAFETY SAFETY LABEL LOCATIONS These labels warn you of potential hazards that can cause serious injury. Read them carefully. If a label comes off or becomes hard to read, contact an authorized Honda servicing dealer for a replacement. CAUTION UNDER NORMAL USAGE, THIS BAG MATERIAL IS SUBJECT TO DETERIORATION AND WEAR, AND SHOULD BE CHECKED FREQUENTLY FOR BAG REPLACEMENT. THIS BAG CONFORMS TO A.N.S.I. STANDARD B71.1, ANY REPLACEMENT MUST MEET THIS STANDARD.
CONTROLS & FEATURES COMPONENT & CONTROL LOCATIONS Use these illustrations to locate and identify the most frequently used controls.
CONTROLS & FEATURES FLYWHEEL BRAKE LEVER DRIVE CLUTCH LEVER SPARK PLUG CAP MODEL NAME AND FRAME SERIAL NUMBER LABEL FUEL VALVE CARBURETOR AIR CLEANER MEETS CPSC BLADE SAFETY REQUIREMENTS.
CONTROLS & FEATURES Fuel Valve The fuel valve opens and closes the fuel passage from the fuel tank to the carburetor. OFF FUEL VALVE ON Throttle Lever The throttle lever controls engine speed and opens and closes the choke. THROTTLE LEVER CHOKE Closes the choke; use when starting a cold engine. FAST For restarting a warm engine and for mowing. SLOW For idling the engine.
CONTROLS & FEATURES Flywheel Brake Lever This lever is connected to the engine flywheel brake and the ignition switch. The engine will not start unless this lever is pushed forward. Drive Clutch Lever The drive clutch lever engages and disengages the transmission speed selected by the shift lever (page 11). FLYWHEEL BRAKE LEVER FLYWHEEL BRAKE LEVER The drive clutch lever operates like a traditional clutch and should always be fully engaged or released in a smooth, even motion.
CONTROLS & FEATURES Shift Lever The shift lever selects and controls the mower’s drive speed. 1 (slow) For mowing thick grass or maneuvering in small areas. 2 (medium) For intermediate self-propelled mowing speed. 3 (fast) For maximum self-propelled transport speed. 1 (SLOW) 2 (MEDIUM) 3 (FAST) SHIFT LEVER Cutting Height Adjustment Levers Each wheel of the mower can be adjusted to one of six settings. The cutting height figures are approximate.
BEFORE OPERATION ARE YOU READY TO GET STARTED? Your safety is your responsibility. A little time spent in preparation will significantly reduce your risk of injury. Knowledge Read and understand this manual. Know what the controls do and how to operate them. Familiarize yourself with the lawn mower and its operation before you begin using it. Know how to quickly shut off the lawn mower in case of an emergency.
BEFORE OPERATION Check the General Condition of the Lawn Mower: • • • • • Look around and underneath the lawn mower for signs of oil or gasoline leaks. Look for signs of damage. Check each control for proper operation. Check the blades for wear. Replace as necessary (page 31). Check that the blade bolts are tight (page 32). Check that all nuts, bolts, screws are tightened. Check the Engine • • Check the air cleaner (page 35) and oil level (page 34). Check the fuel level (page 38).
BEFORE OPERATION GET THE MOWER READY Handlebar Height Adjustment 1. Adjust handlebar height for a comfortable operating position. 2. Loosen the handlebar locking knobs. Spread the lower ends of the handlebar to release the locating pins. 3. Move the handlebar up or down, so the locating pins engage other holes on the handlebar mounting brackets. 4. Tighten the handlebar locking knobs securely.
BEFORE OPERATION Grass Bag A lawn mower works like a vacuum cleaner; it blows air through the bag, which traps the grass clippings. Always empty the grass bag before it becomes filled to the limit of its capacity. Bagging performance will diminish after the bag becomes about 90% filled. Also, the bag is easier to empty when it is not packed full. Inspection Inspect the grass bag for tears, holes, and excessive wear. The grass bag wears during normal use and will eventually require replacement.
BEFORE OPERATION Cutting Height Bagging/Side-Discharge: Move all four adjustment levers to the same position. ADJUSTMENT LEVERS Mulching: Move the front adjustment levers one position higher than the rear levers. To adjust cutting height, pull each adjustment lever toward the wheel, and move it into another notch. If you are not sure what cutting height to select, start with a high setting and check the appearance of the lawn after mowing a small area. Then readjust cutting height if necessary.
OPERATION MOWING PRECAUTIONS Before operating the mower for the first time, please review IMPORTANT SAFETY INFORMATION (page 4) and the previous chapter, BEFORE OPERATION (page 12). Even if you have operated other mowers, take time to become familiar with how this mower works and practice in a safe area until you build up your skills. For your safety, avoid starting or operating the engine in an enclosed area such as a garage.
OPERATION 3. Press the flywheel brake lever against the handlebar and hold them together firmly. Pull the starter grip lightly until you feel resistance, then pull briskly. Return the starter grip gently. 4. If the CHOKE position was used during starting, move the throttle lever away from the CHOKE position as soon as the engine warms up enough to run smoothly without use of the choke. Set the throttle lever at FAST to mow or at SLOW to idle.
OPERATION OPERATING THE CONTROLS FOR MOWING Throttle Lever For best cut quality, always mow with the throttle lever in the FAST position. When the blades rotate at the preset fast speed, it creates a strong fan action that lifts and cuts grass more efficiently. Do not try to increase the preset engine speed: the blade could fracture and come apart. Flywheel Brake Lever The lever must be pushed forward against the handlebar to start the engine.
OPERATION Drive Clutch Lever Push the drive clutch lever forward and hold it against the handlebar to propel the mower forward. BLADE CONTROL LEVER Release the drive clutch lever to stop the mower’s forward movement. Always release the drive clutch lever before starting the engine. If the drive clutch is engaged, the mower will move forward when you operate the starter.
OPERATION STOPPING THE ENGINE 1. Move the throttle lever to SLOW. THROTTLE LEVER SLOW 2. Release the drive clutch lever and flywheel brake lever. FLYWHEEL BRAKE LEVER DRIVE CLUTCH LEVER 3. When the mower is not in use, turn the fuel valve to the OFF position.
OPERATION SAFE MOWING PRACTICES For your safety, keep all four wheels on the ground, and be careful to avoid losing your footing and your control of the mower. Keep a firm grip on the handlebar, and walk, never run, with the mower. Be very careful when mowing uneven or rough ground. If stuck, do not kick or shove the mower with your foot. Use the handlebar to control the mower. WARNING The blade is sharp and spins at high speed. A spinning blade can cut you severely and can amputate fingers and toes.
OPERATION Obstacles Use the side of the mower to cut close to large obstacles, such as fences or walls. Release the drive clutch lever to disengage the drive when mowing around trees and other obstacles. Push the mower around obstacles for better directional control. Be careful when mowing over obstacles embedded in the lawn, such as sprinkler heads, paving, edging, raised tree roots, etc. Avoid anything that sticks up above the surface of the lawn.
OPERATION MOWING TIPS When to Mow Most grasses should be mowed when they have grown 1/2 to 1 inch above their recommended height. More frequent mowing is required for mulching than for bagging. For best results, you may need to mow the lawn twice a week during the growing season. Cutting Height Consult a local nursery or lawn and garden center for cutting height recommendations and advice about specific types of grasses and growing conditions in your area.
OPERATION Blade Speed The blade must spin very fast to cut properly. Always use the FAST throttle setting, and keep the engine running at maximum rpm. If engine speed drops, it could mean the engine is being overloaded by the blade trying to cut too much grass. Mow a narrower swath, move the mower slower, or raise the cutting height. Blade Sharpness A sharp blade cuts cleanly. A dull blade tears the grass, leaving shredded ends that turn brown.
OPERATION Mowing Patterns Your Honda mower will work most efficiently if you use the following mowing patterns as much as possible. Mower deck and equipment design, and the direction in which the blade rotates, cause these mowing patterns to give the best results. Mulching Use a counterclockwise mowing pattern. If the lawn has an irregular shape, or many obstacles, divide it into sections where you can use counterclockwise mowing patterns. Bagging Use a clockwise mowing pattern.
SERVICING YOUR LAWNMOWER THE IMPORTANCE OF MAINTENANCE Good maintenance is essential for safe, economical, and trouble-free operation. It will also help reduce air pollution. WARNING Improper maintenance, or failure to correct a problem before operation, can cause a malfunction in which you can be seriously hurt or killed. Always follow the inspection and maintenance recommendations and schedules in this owner’s manual.
SERVICING YOUR LAWN MOWER MAINTENANCE SAFETY Some of the most important safety precautions follow. However, we cannot warn you of every conceivable hazard that can arise in performing maintenance. Only you can decide whether or not you should perform a given task. WARNING Failure to properly follow maintenance instructions and precautions can cause you to be seriously hurt or killed. Always follow the procedures and precautions in this owner’s manual.
SERVICING YOUR LAWN MOWER MAINTENANCE SCHEDULE ITEM REGULAR SERVICE Before PERIOD each use Blade condition and blade bolt tightness Grass bag Engine oil Air cleaner Spark plug first First month 25 or 5 hours hours Every 50 hours Every 100 hours Every 150 hours See page check { 30 check check change check clean replace filter clean & adjust replace { { 15 34 33 35 35 Spark arrester (optional equipment) clean Idle speed check & adjust Flywheel brake operation Drive clutch cable Flywheel b
SERVICING YOUR LAWN MOWER BLADES Inspection 1. Move the fuel valve to the OFF position (see page 9) and disconnect the spark plug cap from the spark plug (see page 36). 2. Tilt the mower to the right, so the carburetor side is up. This will help to prevent fuel leakage and BLADE BOLTS hard starting. 3. Inspect blades for wear and damage. BLADES WARNING A worn, cracked, or damaged blade can break, and pieces of the damaged blade can become dangerous projectiles. Thrown objects can cause serious injury.
SERVICING YOUR LAWN MOWER Blade Removal and Installation If you remove the blades for sharpening or replacement, you will need a torque wrench for installation. Wear heavy gloves to protect your hands. BLADE SHARPENING: To avoid weakening the blades, or causing imbalance or poor cutting, the blades should be sharpened by trained staff at an authorized Honda servicing dealer. BLADE REPLACEMENT: Use genuine Honda replacement blades or their equivalent (page 63). Blade Removal 1. Turn the fuel valve OFF.
SERVICING YOUR LAWN MOWER Blade Installation 1. Clean dirt and grass from around the blade mounting area. 2. Install the blades using the two blade bolts and special washers as shown. Be sure to install the special washers with the concave side toward the blades and the convex side toward the bolts. The blade bolts and washers are specially designed for this application. When replacing bolts and washers, use only genuine Honda replacement parts. 3. Tighten the blade bolts with a torque wrench.
SERVICING YOUR LAWN MOWER ENGINE MAINTENANCE Engine Oil Change Drain the used oil while the engine is warm. Warm oil drains quickly and completely. 1. Turn the fuel valve OFF (see page 9). This will reduce the possibility of fuel leakage. 2. Wipe the oil filler area clean, then remove the oil filler cap/dipstick. 3. Place a suitable container next to the mower to catch the used oil, then tilt the mower on its right side. The used oil will drain through the filler neck. Allow the oil to drain completely.
SERVICING YOUR LAWN MOWER Engine Oil Level Check 1. Unscrew and remove the filler cap/dipstick and wipe it clean. 2. Insert and remove the dipstick without screwing it into the filler neck. Check the oil level shown on the dipstick. 3. If the oil level is low, add oil to reach the upper limit mark on the dipstick. Do not overfill. If the engine is overfilled, the excess oil may get transferred to the air cleaner housing and air cleaner filters.
SERVICING YOUR LAWN MOWER Air Cleaner Service A dirty air filter will restrict air flow to the carburetor, reducing engine performance. If you operate the mower in very dusty areas, clean the air filter more often than specified in the MAINTENANCE SCHEDULE (page 29). NOTICE Operating the engine without air filters, or with damaged filters, will allow dirt to enter the engine, causing rapid engine wear. This type of damage is not covered by the Distributor’s Limited Warranty (page 64).
SERVICING YOUR LAWN MOWER Spark Plug Service RECOMMENDED SPARK PLUGS REGULAR RESISTOR* NGK BP6ES BPR6ES DENSO W20EP-U W20EPR-U *Resistor spark plugs reduce interference with radio and TV reception. NOTICE Incorrect spark plugs can cause engine damage. For good performance, the spark plug must be properly gapped and free of deposits. 1. Disconnect the spark plug cap and remove any dirt from around the spark plug area. SPARK PLUG SPARK PLUG CAP 2.
SERVICING YOUR LAWN MOWER 4. Measure the spark plug electrode gap with a suitable gauge. The gap should be 0.028 ~ 0.031 in (0.7 ~ 0.8 mm). Correct the gap, if necessary, by carefully bending the side electrode. 5. Install the spark plug carefully, by hand, to avoid crossthreading. 0.028 ~ 0.031 in (0.7 ~ 0.8 mm) 6. After the spark plug seats, tighten with a 13/16 in (21 mm) spark plug wrench to compress the washer. If reinstalling the old spark plug, tighten 1/8 to 1/4 turn after the spark plug seats.
SERVICING YOUR LAWN MOWER FUEL Fuel Information This engine is certified to operate on unleaded gasoline with a pump octane rating of 86 or higher. Unleaded gasoline produces fewer engine and spark plug deposits and extends exhaust system life. Never use stale or contaminated gasoline or an oil/gasoline mixture. Avoid getting dirt or water in the fuel tank. Occasionally you may hear light “spark knock” or “pinging” (metallic rapping noise) while operating under heavy loads. This is no cause for concern.
SERVICING YOUR LAWN MOWER Refueling Fuel tank capacity: 0.29 US gal (1.1 liter) Use unleaded gasoline with a pump octane rating of 86 or higher. Refuel in a well-ventilated area before starting the engine. If the engine has been running, allow it to cool. Refer to page 55 for information about oxygenated fuels. WARNING Gasoline is highly flammable and explosive. You can be burned or seriously injured when handling fuel. • • • Stop the engine and keep heat, sparks, and flame away.
SERVICING YOUR LAWN MOWER CONTROL CABLE ADJUSTMENTS Flywheel Brake Cable Adjustment 1. Measure free play at the top of the flywheel brake lever. Free play should be 3/16 ~ 3/8 in (5 ~ 10 mm). If adjustment is necessary: 2. Loosen the lock nuts with a 10 mm wrench, and move the adjuster up or down as required. 3. Tighten the lock nuts and recheck free play. 4. Start the engine outdoors. Move the throttle to FAST. Release the flywheel brake lever; the engine should stop quickly.
SERVICING YOUR LAWN MOWER Drive Clutch Cable Adjustment 1. Measure free play at the top of the lever, as shown. Free play should be 1/16 ~ 3/16 in (1 ~ 5 mm). If adjustment is necessary: 2. Loosen the lock nuts with a 10 mm wrench, and move the adjuster up or down as required. 3. Tighten the lock nuts and recheck free play. 4. Start the engine outdoors, and operate the drive clutch lever. Check that the drive clutch engages and releases properly.
SERVICING YOUR LAWN MOWER Shift Cable Adjustment Shift cable adjustment is necessary if the shift lever does not operate smoothly, does not shift properly into a gear, or does not align with the numbers beside the lever. With the shift lever in 2nd gear, check that the lever, throughout its free play range, is well-centered on the number “2” on the lever cover. If adjustment is necessary: 1. Loosen the lock nuts with a 10 mm wrench, and move the adjuster up or down as required. 2.
SERVICING YOUR LAWN MOWER Throttle Cable Inspection Throttle cable adjustment is necessary if the throttle lever does not operate the choke properly. You can inspect choke operation by observing the movement of the choke arm, which is located on top of the carburetor. 1. Move the throttle lever to the FAST position. 2. Remove the air cleaner cover (see page 35). FAST THROTTLE LEVER 3. Use a feeler gauge and measure the clearance between the control choke arm and the control lever.
SERVICING YOUR LAWN MOWER GRASS BAG CLEANING AND REPLACEMENT Grass Bag Cleaning Wash the bag with a garden hose, and allow it to dry completely before use; a wet bag will clog quickly. Grass Bag Replacement Replace a worn or damaged bag with a Honda replacement bag or its equivalent (page 63). Bag Removal 1. Unclip the plastic edges of the bag from the frame. BAG 2. Remove the bag from the frame. PLASTIC EDGE FRAME Bag Installation 1. Insert the bag frame into the bag, as shown. 2.
STORAGE STORAGE PREPARATION Proper storage preparation is essential for keeping your lawn mower trouble free and looking good. The following steps will help to keep rust and corrosion from impairing your lawn mower’s function and appearance, and will make the engine easier to start when you use the lawn mower again. Cleaning 1. Wash the lawn mower, including the underside of the mower deck. Engine Wash the engine by hand, and be careful to prevent water from entering the air cleaner.
STORAGE 3. With the mower in an upright position, start the engine outdoors, and let it run until it reaches normal operating temperature to evaporate any water remaining on the engine. 4. Stop the engine and allow it to cool. 5. After the lawn mower is clean and dry, touch up any damaged paint (touch-up paint part numbers are on page 63), and coat other areas that may rust with a light film of oil. Lubricate the control cable cores with a silicone spray lubricant (page 63).
STORAGE Fuel Gasoline will oxidize and deteriorate in storage. Old gasoline will cause hard starting, and it leaves gum deposits that clog the fuel system. If the gasoline in your mower deteriorates during storage, you may need to have the carburetor and other fuel system components, serviced or replaced.
STORAGE Draining the Carburetor and Fuel Tank 1. Make sure the fuel valve is OFF (see page 9). Remove the carburetor drain bolt with a 10 mm wrench, and drain the fuel from the carburetor bowl into an approved container. WARNING Gasoline is highly flammable and explosive. You can be burned or seriously injured when handling fuel. • • • Stop engine and keep heat, sparks, and flame away. Handle fuel only outdoors. Wipe up spills immediately. If you only wish to drain the carburetor, skip to step 3. 2.
STORAGE Engine Cylinder Remove the spark plug (see page 36). Pour a tablespoon (5 ~ 10 cc) of clean engine oil into the cylinder. Pull the starter rope several times to distribute the oil in the cylinder. Reinstall the spark plug. Pull the starter rope slowly until resistance is felt then return the starter grip gently. This will close the valves so moisture can not enter the engine cylinder.
STORAGE PLACING IN STORAGE If your mower will be stored with gasoline in the fuel tank and carburetor, it is important to reduce the hazard of gasoline vapor ignition. Select a well-ventilated storage area away from any appliance that operates with a flame, such as a furnace, water heater, or clothes dryer. Also avoid any area with a spark-producing electric motor, or where power tools are operated. If possible, avoid storage areas with high humidity, because that promotes rust and corrosion.
TRANSPORTING BEFORE LOADING If the engine has been running, allow it to cool for at least 15 minutes before loading the mower on the transport vehicle. A hot engine and exhaust system can burn you and can ignite some materials. 1. Turn the fuel valve to the OFF position. This will prevent carburetor flooding and reduce the possibility of fuel leakage. OFF FUEL VALVE 2. If installed, remove the grass bag.
TAKING CARE OF UNEXPECTED PROBLEMS ENGINE PROBLEMS Engine Will Not Start 1. Check control positions. 2. Check fuel. 3. Remove and inspect spark plug. 4. Take the mower to an authorized Honda servicing dealer, or refer to shop manual. Loss of Power Possible Cause Correction Fuel valve OFF. Turn fuel valve ON (page 9). Throttle lever in wrong position. Move throttle lever to CHOKE position, unless the engine is warm (page 17). Flywheel brake lever not engaged.
TAKING CARE OF UNEXPECTED PROBLEMS VIBRATION PROBLEMS Excessive Vibration 1. Check mower deck and blades. 2. Take the mower to an authorized Honda servicing dealer for repair. Possible Cause Correction Grass and debris lodged under mower deck. Clear out mower deck (page 25). Blades loose, bent, damaged, or unbalanced by improper sharpening. Tighten loose blades bolts. Replace damaged blades (page 32). Mechanical damage, such as a bent crankshaft. Replace or repair faulty components as necessary.
TECHNICAL & CONSUMER INFORMATION TECHNICAL INFORMATION Serial Numbers Record the engine and frame serial numbers (locations are shown on page 8) in the spaces below. You may need these serial numbers when ordering parts, and when making technical or warranty inquiries (page 68).
TECHNICAL & CONSUMER INFORMATION Spark Arrester Service (optional equipment) Your lawn mower engine is not factory-equipped with a spark arrester. In some areas, it is illegal to operate an engine without a spark arrester. Check local laws and regulations. An optional USDA approved spark arrester is available from an authorized Honda servicing dealer. The spark arrester must be serviced every 100 hours to keep it functioning as designed. 1.
TECHNICAL & CONSUMER INFORMATION Oxygenated Fuels Some conventional gasolines are being blended with alcohol or an ether compound. These gasolines are collectively referred to as oxygenated fuels. To meet clean air standards, some areas of the United States and Canada use oxygenated fuels to help reduce emissions. If you use an oxygenated fuel, be sure it is unleaded and meets the minimum octane rating requirement. Before using an oxygenated fuel, try to confirm the fuel's contents.
TECHNICAL & CONSUMER INFORMATION EMISSION CONTROL SYSTEM Source of Emissions The combustion process produces carbon monoxide, oxides of nitrogen, and hydrocarbons. Control of hydrocarbons and oxides of nitrogen is very important because, under certain conditions, they react to form photochemical smog when subjected to sunlight. Carbon monoxide does not react in the same way, but it is toxic.
TECHNICAL & CONSUMER INFORMATION Air Index An Air Index Information hang tag/label is applied to engines certified to an emission durability time period in accordance with the requirements of the California Air Resources Board. The bar graph is intended to provide you, our customer, the ability to compare the emissions performance of available engines. The lower the Air Index, the less pollution.
TECHNICAL & CONSUMER INFORMATION Replacement Parts The emission control systems on your new Honda engine were designed, built, and certified to conform with EPA and California emission regulations. We recommend the use of genuine Honda parts whenever you have maintenance done. These original-design replacement parts are manufactured to the same standards as the original parts, so you can be confident of their performance.
TECHNICAL & CONSUMER INFORMATION SPECIFICATIONS Mower Model HRB216TDA Honda rotary mower, 21 inch mower deck, 5.5 hp, three-speed transmission, zone start, USA market Dimensions, Weights and Capacities Length 70 in (1779 mm) Width at Mower Deck 23-1/4 in (590 mm) Height 46-1/2 in (1180 mm) Dry Weight 81.6 lb (37.
TECHNICAL & CONSUMER INFORMATION Maintenance Fuel Unleaded gasoline with a pump octane rating of 86 or higher. See page 39. Engine Oil SAE 10W-30, API SH or SJ See page 34. Spark Plug Type Regular: NGK - BP6ES or DENSO - W20EP-U Resistor: NGK - BPR6ES or DENSO - W20EPR-U See page 36. Maximum Governed Speed 2,950 ~ 3,100 rpm See shop manual. Flywheel Brake Cable Adjust for 3/16~3/8 in (5~10) free play at flywheel brake lever. See page 40.
TECHNICAL & CONSUMER INFORMATION CONSUMER INFORMATION Find an Authorized Honda Servicing Dealer in Your Area Visit our website: www.hondapowerequipment.com Customer Service See page 68. Honda Publications These publications will give you additional information for maintaining and repairing your lawnmower. You may order them from an authorized Honda servicing dealer. Shop Manual: This manual covers complete maintenance and overhaul procedures. It is intended to be used by a skilled technician.
TECHNICAL & CONSUMER INFORMATION Replacement Parts. Optional Equipment and Service Items Contact an authorized Honda servicing dealer to purchase any of these (or other) genuine, original Honda items for your lawnmower.
TECHNICAL & CONSUMER INFORMATION Distributor's Limited Warranty PRODUCTS COVERED BY THIS WARRANTY LENGTH OF WARRANTY (from date of original retail purchase) Noncommercial/Nonrental Commercial/Rental Harmony Lawnmower 24 months 3 months Harmony Xenoy Mower Deck 60 months 3 months Parts & Accessories See your authorized Honda servicing dealer for details To Qualify for this Warranty: The product must be purchased in the United States, Puerto Rico, or the U.S.
TECHNICAL & CONSUMER INFORMATION Emission Control System Warranty Your new Honda Power Equipment engine complies with both the U.S. EPA and State of California emission regulations. American Honda provides the same emission warranty coverage for engines sold in all 50 states. Your Warranty Rights And Obligations: California The California Air Resources Board and American Honda Motor Co., Inc. are pleased to explain the emission control system warranty on your Honda Power Equipment engine.
TECHNICAL & CONSUMER INFORMATION Warranty Coverage: Honda power equipment engines manufactured after January 1, 1995 and sold in the State of California, and U.S. EPA certified engines manufactured on or after September 1, 1996 and sold in all of the United States, are covered by this warranty for a period of two years from the date of delivery to the original retail purchaser. This warranty is transferable to each subsequent purchaser for the duration of the warranty period.
TECHNICAL & CONSUMER INFORMATION Exclusions: FAILURES OTHER THAN THOSE RESULTING FROM DEFECTS IN MATERIAL OR WORKMANSHIP ARE NOT COVERED BY THIS WARRANTY. THIS WARRANTY DOES NOT EXTEND TO EMISSION CONTROL SYSTEMS OR PARTS WHICH ARE AFFECTED OR DAMAGED BY OWNER ABUSE, NEGLECT, IMPROPER MAINTENANCE, MISUSE, MISFUELING, IMPROPER STORAGE, ACCIDENT AND/ OR COLLISION, THE INCORPORATION OF, OR ANY USE OF, ANY ADD-ON OR MODIFIED PARTS, UNSUITABLE ATTACHMENTS, OR THE UNAUTHORIZED ALTERATION OF ANY PART.
TECHNICAL & CONSUMER INFORMATION Customer Service Information Honda Power Equipment dealership personnel are trained professionals. They should be able to answer any question you may have. If you encounter a problem that your dealer does not solve to your satisfaction, please discuss it with the dealership's management. The Service Manager or General Manager can help. Almost all problems are solved in this way.
INDEX A Accessories. See Parts Air Cleaner Service ........................... 35 Air Filter Part Number ....................... 63 Air Index ............................................ 58 Altitude, High Altitude Operation ....... 54 B Bag. See Grass Bag Before Operation............................... 12 Blades Inspection....................................... 30 Installation ...................................... 32 Part Numbers .................................
INDEX Change........................................... 33 Level Check.................................... 34 Part Number ................................... 63 Recommended ............................... 34 P Paint, Part Number............................ 63 Parts, Replacement & Optional ......... 63 Publications ....................................... 62 S Safety A few words ...................................... 2 Information ....................................... 4 Label Locations ...................
QUICK REFERENCE INFORMATION B WARNING: B The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Fuel type Unleaded gasoline with a pum p octane of 86 or higher Engine Oil Spark Plug capacity 0.29 U.S. gallon (1.1 liter) type SAE 10W-30 capacity 0.58 U.S. quart (0.
® Owner’s Manual Rotary Mower HRB216TDA ® EM3 POM53249-C 31VE2752 00X31-VE2-7520 Printed on Recycled Paper IPC 10000.2002.04 PRINTED IN U.S.A. © 1997, 2000–2002 American Honda Motor Co., Inc.
