User Manual

ManualsBrandsHON HAI Precision Ind ManualsElectronicsWLAN & Bluetooth combo module

.!2!.!

MARVELL 88W8688 Mini-Module

(IEEE 802.11b/g+BT 2.1 EDR)

Marketing Requirements Specification

T77H134.00

< REV.05>

Prepared by Reviewed by Approved by

Plum Feng Robin Xu Chang-fu Lin

WLAN & BT combo module

WLAN and Bluetooth

combo module

Summary of content (10 pages)

PAGE 1
WLAN and Bluetooth WLAN & BT combo module MARVELLcombo 88W8688 Mini-Module module (IEEE 802.11b/g+BT 2.1 EDR) Marketing Requirements Specification T77H134.00 < REV.05> Prepared by Plum Feng Reviewed by Robin .!2!.
PAGE 2
CONTENTS 0. REVISION HISTORY..............................................................................................................................................3 1. INTRODUCTION ..........................................................................................................................................................4 1.1 SCOPE ...........................................................................................................................................................
PAGE 3
0. Revision History Date Change Note REV Note Nov. 11, 2008 Rev.01 0 Dec. 19, 2008 Rev.02 Update dimension of module Apr. 28, 2009 Rev.03 Change the pin-define Oct. 13.2009 Rev.04 Change the height of shielding Oct. 27.2009 Rev.05 Change the mechanical spec of shielding .!4!.
PAGE 4
1. Introduction Project Name: Mini-Module (802.11b/g + BT Module) based on Marvell IC 88W8688 with TFBGA package. This documentation describes the Engineering requirements specification of the WLAN (802.11b/g) +Bluetooth 2.1 EDR Mini-Module. It is a confidential document of FOXCONN. 1.1 Scope The Wireless MARVELL 88W8688BFL Mini-Module is designed to support 802.11g data rate of 54, 48, 36, 24, 18, 12, 9, 6Mbps, and as well as 802.11b data rate of 11, 5.5, 2, 1Mbps for WLAN operation.
PAGE 5
2 Product Specification 2.1 Hardware Specification 2.1.1 WLAN Wireless LAN Standards Operating Frequency Channel Numbers WLAN Data Rate Modulation Schemes Transmitter Output Power EVM Receiver Sensitivity Media Access Protocol IEEE 802.11g standard and IEEE 802.11b 2.412~2.484GHz 11 channels for United States and Taiwan. 13 channels for Europe Countries 14 channels for Japan 802.11g: 54Mbps with fall back of 48, 36, 24, 18, 12, 9, 6Mbps. 802.11b: 11Mbps with fall back rates of 5.5, 2, and 1Mbps 802.
PAGE 6
3. Product Requirements 3.1 Hardware Requirements Form factor Host Interface PCB Antenna port: LGA SDIO 6-layer FR4 One BT RF port and One Wi-Fi RF port 3.2 Hardware Architecture The module design is based on the MARVELL 88W8688BFL single chip which implements IEEE802.11b/g and Bluetooth 2.1+EDR. Figure 1 Functional Block Diagram MARVELL 88W8688BFL is a highly integrated, low-cost, low-power IEEE802.11 b/g MAC /Baseband / RF WLAN and Bluetooth Baseband/RF.
PAGE 7
Federal Communication 3.3 Mechanical outline Drawing Commission Interference Statement This equipment has been and found to comply with the limits for a Class digital device, The MARVELL 8688 tested Mini-Module 802.11b/g module shall be 6-layer PCB Bdesign. pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection Dimension (W×L×H): 10.8mm ×15.8mm ×2.1mm (max.) against harmful interference in a residential installation.
PAGE 8
3.4 Land Grid Array 3.4.1 LGA assignment and location˄ ˄top view˅ ˅ IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization.
PAGE 9
3.4.2 Pin definition Pin name PIN# Function NCC ᤞ፿ : TCK C2 JTAG test clock input TDI F4 JTAG test data input ᆖী‫ڤ‬ᎁᢞ‫ٽ‬௑հ‫פ܅‬෷୴᙮ሽᖲΔॺᆖ๺‫ױ‬Δֆ‫׹‬Ε೸ᇆࢨࠌ‫݁ृش‬լ൓ᖐ۞᧢‫ޓ‬᙮෷Ε‫!!!ף‬ TDO E3 JTAG test data output Օ‫פ‬෷ࢨ᧢‫଺ޓ‬๻ૠհ௽ࢤ֗‫פ‬౨Ζ TMS2 D4 JTAG test mode select. Selects the system JTAG controller TRSTn C4 JTAG test reset(active low) JTAG test mode select.
PAGE 10
3.5 Software Requirements The software includes firmware, driver and configuration utility for Wireless WLAN 802.11 b/g + Bluetooth Module based on Marvell 88w8688BFL chip. 3.5.1 Software setup The software components required for operations will be packed into one installation program, thus user and customer can setup and upgrade software simply by running the setup program (ex. Setup.exe) without any obstacles. 3.5.