Foxconn Bluetooth Module User Manual J27H007 Foxconn Bluetooth Module User Manual Revision 1.
Foxconn Bluetooth Module User Manual Revision History Revision 1.
Foxconn Bluetooth Module User Manual 1. Overview....................................................................................................................... 4 1.1 Setup PC.................................................................................................................. 4 1.2 Writing firmware ....................................................................................................... 4 2. Install the Applications .........................................................
Foxconn Bluetooth Module User Manual 1. Overview 1.1 Setup PC Bluetooth module development is necessary to setup your PC. Broadcom Bluetool and Active Peal must be installed your PC. Two USB Drivers must be Installed your PC. This documentation is the support guide for starting your development. 1.2 Writing firmware Bluetooth module must be written the firmware. This documentation is the support guide for writing the firmware. 2. Install the Applications 2.1 Applications ActivePerl 5.8.4.
Foxconn Bluetooth Module User Manual 3.1 Plug-in Plug-in your Bluetooth module. Confirm USB D+ to be pull up. Host PC will detect USB device. 3.2 Install USB driver Install USB driver Nintendo tendered. This USB driver revision is 5.1.0.200. Confirm Bluetooth device at device manager. 3.3 Starting Bluetool From the start menu, select Broadcom Bluetool and then the Bluetool icon. Bluetool displays an empty window the first time that is run.
Foxconn Bluetooth Module User Manual 3.4 Open USB Interface From the transport menu, select HCI control Check USB, and select pull-down menu usb0, click OK. 3.5 Log window From the View menu, select Log window.
Foxconn Bluetooth Module User Manual 3.6 HCI command transport to Bluetooth module From HCI Control window, click Reset.
Foxconn Bluetooth Module User Manual 4. Write Nintendo firmware 4.1. Prepare to write Before writing firmware, from pull-down menu on HCI control window, select 0:Vender-specific Commands. Click “Download Minidriver”. 4.2. Set download components. From the transport menu, select Download and Firmware/Config….. Check USB, and select pull-down menu usb0, click OK.
Foxconn Bluetooth Module User Manual From Download menu, click Import. Import Nintendo.btp file. This import file is EEPROM setting files for Nintendo firmware. Confirm device configuration is selected “Nintendo B3 ROM + eeprom 32 byte pages” Set Download minidriver. Select usb.hex file. It is default so, not to change. Set Download configuration record. Select BCM2042B3_002.003.014.0167.0000.cgr file. Set BD_ADDR. BD_ADDR is same as MAC address.
Foxconn Bluetooth Module User Manual Click Execute. So Writing firmware will start. 5. Set nintendo module 5.1 Remove USB D+ pull-up USB pull-up must be removed because nintendo module (writing nintendo firmware module) has internal USB pull-up resistor. If not remove, Host PC recognize wrong device. 5.2 GPIO Default Status GPIO must be set as follows table.
Foxconn Bluetooth Module User Manual 5.3 Install Nintendo USB driver Nintendo USB driver must be installed. USD Vender ID and product ID of nintendo module is not same as it of Pre-write module. Nintendo USB driver revision is 5.1.0.200(Nintendo). Confirm Bluetooth device at device manager.
This device is intended only for OEM integrators under the following conditions: The antenna must be installed such that 20 cm is maintained between the antenna and users. As long as conditions above is met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.).
End Product Manual Information The user manual for end users must include the following information in a prominent location "IMPORTANT NOTE": To comply with FCC RF exposure compliance requirements, the antenna used for this transmitter must be installed to provide a separation distance of at least 20cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.
如果使用本模組之平台, 無法在外部看見審驗合格標籤時, 應在該平台的外部明 顯標示內含射頻模組"CCXXxxYYyyyZzW"字樣.
