User's Manual

ManualsBrandsHON HAI Precision Ind ManualsElectronicsBluetooth Module

COMPANY CONFIDENTIAL

Part Name Bluetooth Module

Doc. Rev. 0.0

Foxconn P/N. J20H077.00

Prepared by Reviewed by Approved by

Kevin Tao Eddie Huang

User Manual

Bluetooth Module

Summary of content (24 pages)

PAGE 1
COMPANY CONFIDENTIAL User Manual Bluetooth Module Part Name Bluetooth Module Doc. Rev. Foxconn P/N. Prepared by Kevin Tao 0.0 J20H077.
PAGE 2
COMPANY CONFIDENTIAL Content Section1 Introduction ..............................................................................................................3 1. Product Overview ................................................................................................................3 1.1 Application scope..................................................................................................... 3 1.2 Block Diagram.........................................................................
PAGE 3
COMPANY CONFIDENTIAL Section1 Introduction 1. Product Overview The J20H077.00 Bluetooth module provides Bluetooth 3.0 compliant wireless modem function. This module is based on BCM20705 solution which is integrated 2.4GHz transceiver and manufactured using the industry’s most advanced 65nm CMOS low-power process. 1.1 Application scope The BT Module is compliant to Bluetooth 3.0 and EDR standard: Carrier Frequency: 2402MHz ~ 2480 MHz Carrier Spacing: 1.
PAGE 4
COMPANY CONFIDENTIAL 1.3 Features i i i i i Bluetooth 3.0 Compliant UART Interface. Module is powered by the host with a 3.3V +/- 10% supply. One PCB printed antenna. 4 layers through hole PCB design with halogen free FR4 material 1.
PAGE 5
COMPANY CONFIDENTIAL 2. Electrical Specification 2.1 Recommended operating rating Element Symbol Min Typ Max Unit DC supply voltage UV+ 3.0 3.3 3.6 (V) 2.2 DC Characteristics Parameter Min Typ Max Unit Supply voltage Tx Current 3.0 - 3.3 40 3.6 50 (V) (mA) Rx Current Standby Current - 26 5 32 7 (mA) (mA) Symbol STBY3.3V 2.3 ESD Information Mode Level Unit HBM MM +/-1500 +/-200 V V 2.
PAGE 6
COMPANY CONFIDENTIAL 3. RF Specification 3.1 Bluetooth 3.0 Items Contents Max. Unit 1 3 dBm -75 6 75 kHz DH1 DH3 -20 -20 -4 -4 20 20 kHz/50us kHz/50us DH5 Average Drift -20 -5 20 kHz/50us DH1 -25 -1 25 DH3 -40 0 40 kHz kHz DH5 -40 0 40 F1avg 140 150 175 F2max 115 140 kHz kHz F1/F2 Ratio 5. EDR Relative Transmit Power 0.8 0.96 2Mbps: P[DQPSK]-P[GFSK] -4 0.25 1 dB 3Mbps: P[8DPSK]-P[GFSK] -4 0.
PAGE 7
COMPANY CONFIDENTIAL Items Specification Frequency range Data rate - RX Characteristics 1. Minimum Input Level Sensitivity GFSK (1Mbps) ±/4 DQPSK (2Mbps) Contents BT3.0 2.4GHz~2.4835GHz 1Mbps, 2Mbps, 3Mbps Min. Typ. Max. ʳ ʳ ʳ -90 -83 -90 -83 8DPSK (3Mbps) Unit ʳ dBm dBm - -85 -77 dBm ʳ ʳ ʳ ʳ GFSK (1Mbps) -20 0 dBm ±/4 DQPSK (2Mbps) -20 -14 dBm 8DPSK (3Mbps) -20 -14 dBm 2. Maximum Input Level 3.2 Antenna Characteristic Parameter Value Units 2402~2483.
PAGE 8
COMPANY CONFIDENTIAL 4. Mechanical Specifications 4.1 PCB Assembly Dimension Dimension (W x L ): 34.
PAGE 9
COMPANY CONFIDENTIAL Section2 WinXP utility and install 5. Overview This document is intended to provide a brief introduction to the Mckinley test for users. It includes the initial setup instruction on how to configure the device and test the transmitter. 6. Requirements Hardware - Desktop PC with USB interface Software - Windows XP Professional (SP3 or above) - USB to UART DRIVER - Bluetooth Test Tool 7. USB to UART Interface Driver Install Step1: Go to “* \BT\Test Tool\uart driver\V6.
PAGE 10
COMPANY CONFIDENTIAL Step2: Select “Launch the CP210x VCP Driver Installer”, and click the “Finish” button to start the install. Step3: Finish installation and Insert the Conversion Board with Module, you will get a card named”Silicon Labs CP210x USB to UART Bridge” in computer management..
PAGE 11
COMPANY CONFIDENTIAL 8. Test Tool Install 8.1 ActivePerl-5[1].8.4.810-MSWin32-x86.msi install Step1: Go to “* \BT\Test Tool” and double click “ActivePerl-5[1].8.4.810-MSWin32-x86.msi” to install Step2: Select the default setting, and then click the “Next>” button to show the next page. Step3: Select ”Enable PPM3 to send profile info to ASPN ”, and then click the “Next>” button to show the next page.
PAGE 12
COMPANY CONFIDENTIAL Step4: Select the default setting, and then click the “Next>” button to continue the installation. 8.2 dotnetfx.exe install Step1: Go to “* \BT\Test Tool” and double click “dotnetfx.exe” to install Microsoft.net Framework 1.1 8.3 setup_for 20702A1.exe Step1: Go to “* \BT\Test Tool” and double click “setup_for 20702A1.exe” to install BlueTool Step2: Select the “Typical”, and then click the “Next>” button to continue the installation.
PAGE 13
COMPANY CONFIDENTIAL Step3: Click the “Finish” button to finish the installation.
PAGE 14
COMPANY CONFIDENTIAL 9. Blue Tool Test Setting 9.1 Tx Mode Step1: Go to “C:\Program Files\Broadcom\BlueTool “to double click the “BlueTool.
PAGE 15
COMPANY CONFIDENTIAL Step3: Select “Transport ->HCI Control.. “to select the interface based on the computer management.
PAGE 16
COMPANY CONFIDENTIAL Step4: Select “7.3: Host controller & Baseband Commands(3 Key) “ and do “Reset” . Step5: Select “7.
PAGE 17
COMPANY CONFIDENTIAL Step6: Select “0: Verdor-specific Commands(0 Key) “ and do “Tx Test” to set Tx Mode Step7: Select “0: Verdor-specific Commands(0 Key) “ and do “Tx Test” to set Tx Mode, set packet type DH5,output power 10dBm , then click “OK”
PAGE 18
COMPANY CONFIDENTIAL 9.2 Frequency Deviation Test Step1: Based on Section 9.1 Step5 , Select “0: Verdor-specific Commands(0 Key) and do “Set Tx Carrier Frequency ARM” to set Frequency Deviation Test . Step2: Select frequency for Frequency Deviation Test .
PAGE 19
COMPANY CONFIDENTIAL 9.3 Rx Mode Step1: Based on Section 4.1 Step5 , Select “0: Verdor-specific Commands(0 Key) “ and do “write receive only” to set Rx Mode .
PAGE 20
Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
PAGE 21
This device is intended only for OEM integrators under the following conditions: The transmitter module may not be co-located with any other transmitter or antenna. As long as the conditions above are met, further transmitter test will not be required.
PAGE 22
Industry Canada statement: This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada applicable aux appareils radio exempts de licence.
PAGE 23
Tant que les le conditions ci-dessus sont remplies, des essais supplémentaires sur l'émetteur ne seront pas nécessaires. Toutefois, l'intégrateur OEM est toujours responsable des essais sur son produit final pour toutes exigences de conformité supplémentaires requis pour ce module installé.
PAGE 24
Manuel d'information à l'utilisateur final L'intégrateur OEM doit être conscient de ne pas fournir des informations à l'utilisateur final quant à la façon d'installer ou de supprimer ce module RF dans le manuel de l'utilisateur du produit final qui intègre ce module. Le manuel de l'utilisateur final doit inclure toutes les informations réglementaires requises et avertissements comme indiquͼ dans ce manuel.