HON HAI PRECISION IND. CO., LTD. No.2, 2nd Dong Huan Road, 10th YouSong lndustrial District, Longhua Town, Baoan, ShenZhen User Manual WiFi+ BT Module Project Name Approval Sheet Rev. Foxconn Part No. Prepared by Shu-yu Li WiFi+ BT Module 1.
CONTENTS 1 PRODUCT INTRODUCTION .............................................................. 3 1.1 2 MODULE HARDWARE OVERVIEW ........................................................ 4 2.1 2.2 2.3 3 ABSOLUTE MAXIMUM RATING ............................................................... 6 RECOMMENDED OPERATING RATING ......................................................... 6 DC CHARACTERISTICS ................................................................... 6 ESD INFORMATION ......................
1 Product Introduction The J20H064 802.11b/g/n+Bluetooth4.0 module provides wireless modem functionality utilizing direct sequence spread spectrum and OFDM/CCK technology. This module is based on Marvell 88W8766P solution which is integrated 2.4GHz IEEE802.11 b/g/n (MAC/baseband/radio), Bluetooth 4.0 + High speed and power amplifiers (PA). 1.1 Application scope The wireless LAN is compliant to IEEE 802.11b and IEEE 802.11g and IEEE 802.11n standard. The data rate of 802.
2 Module Hardware Overview 2.1 Block Diagram The general HW architecture is shown below Figure: . Module Block Diagram 2.2 Features ♦ ♦ ♦ ♦ ♦ ♦ IEEE802.11b/g/n (1X1) and Bluetooth 4.0 based on Marvell 88W8766P solution. USB 2.0 Interface, High and Full Speeds supported. Module is powered by the host with a 5.0V +/- 5% supply. External PCB printed antennas. Two SPDT switch for antenna diversity and Bluetooth function. 2 layers single side design, through hole PCB design with halogen free FR4 material 2.
Pin Number 1 2 3 4 5 S1 S2 Symbol Name GND DP DM UV+ GND GND GND Status I/O I/O P 5 Pin definition Ground USB positive data USB negative data USB +5V power input Ground Ground Ground
3 Electrical Specification 3.1 Absolute maximum rating Element DC supply voltage 3.2 UV+ Symbol UV+ Min 4.5 Max 6.5 Unit (V) Typ 5.0 Max 5.5 Unit (V) Parameter Supply voltage Min 4.5 Typ 5.0 Max 5.
4 RF Specification 4.1 IEEE802.11b Items Contents Specification Mode Channel Data rate TX Characteristics 1. Power Levels (Calibrated) 1) Target Power@1Mbps 2) Target Power@2Mbps 3) Target Power@5.5Mbps 4) Target Power@11Mbps 2. Spectrum Mask @16dBm 1) fc-33MHz ＜ f ＜ fc-22MHz 2) fc-22MHz ＜ f ＜ fc-11MHz 3) fc+11MHz ＜ f ＜ fc+22MHz 4) fc+22MHz ＜ f ＜ fc+33MHz 3. Frequency Error 4 Modulation Accuracy(EVM)@16dBm 1) 1Mbps 2) 2Mbps 3) 5.
4.2 IEEE802.11g Items Contents Specification Mode Channel Data rate TX Characteristics 1. Power Levels (Calibrated) 1) Target Power@6Mbps 2) Target Power@9Mbps 3) Target Power@12Mbps 4) Target Power@18Mbps 5) Target Power@24Mbps 6) Target Power@36Mbps 7) Target Power@48Mbps 8) Target Power@54Mbps 2.
4.3 802.11n HT20 Items Contents Specification Mode Channel Data rate (MCS index) TX Characteristics 1. Power Levels (Calibrated) 1) Target Power@MCS0 2) Target Power@ MCS1 3) Target Power@ MCS2 4) Target Power@ MCS3 5) Target Power@ MCS4 6) Target Power@ MCS5 7) Target Power@ MCS6 8) Target Power@ MCS7 2. Spectrum Mask @14dBm 1) at fc +/- 11MHz 2) at fc +/- 20MHz 3) at fc > +/-30MHz 3. Modulation Accuracy(EVM)@14dBm 1) MCS0 2) MCS1 3) MCS2 4) MCS3 5) MCS4 6) MCS5 7) MCS6 8) MCS7 4.
5 Operation SOP 1: Install normal driver under Linux PC 2: search WiFi AP and double click to make connection 3: If connection setup is ok, PC can communicate with network through wireless AP.
Items Contents BT4.0+EDR Specification Frequency range Data rate 2.4GHz~2.4835GHz 1Mbps, 2Mbps, 3Mbps Min. Typ. Max. - TX Characteristics - Unit 1. Power Levels BT Output Power -3 1 3 dBm 2. Initial Carrier Frequency Tolerance Average Offset -75 2 75 kHz DH1 DH3 -20 -20 -3 0 20 20 kHz/50us kHz/50us DH5 Average Drift -20 4 20 kHz/50us DH1 -25 -3 25 DH3 -40 -4 40 kHz kHz DH5 -40 -5 40 F1avg 140 164 175 F2max 115 135 kHz kHz F1/F2 Ratio 5.
Items Contents BT4.0+EDR Specification Frequency range Data rate 2.4GHz~2.4835GHz 1Mbps, 2Mbps, 3Mbps Min. Typ. Max. - RX Characteristics - Unit 1. Minimum Input Level Sensitivity GFSK (1Mbps) - - -79 dBm π/4 DQPSK (2Mbps) - - -72 dBm 8DPSK (3Mbps) - - -72 dBm GFSK (1Mbps) -20 0 dBm π/4 DQPSK (2Mbps) -20 0 dBm 8DPSK (3Mbps) -20 0 dBm 30MHz- 1GHz - - -57 dBm 1GHz – 13.2GHz - - -47 dBm 2. Maximum Input Level 3.
6 Mechanical Specifications 6.1 Shielding Cover Dimension Dimension (LxWxH): 20.32mm x 18.28mm x 2.4mm Thickness: 0.
6.2 PCB Assembly Dimension Dimension (W x Lx H ): 51.8mmx20mmx0.9mm PCB: 2 layer HF-FR4 design Industry Canada statement: This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
(For module device use) 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed.
Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: “Contains FCC ID: MCLJ20H064”. The grantee's FCC ID can be used only when all FCC compliance requirements are met.
Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 17: Specific conditions for 2,4 GHz wideband transmission systems and 5 GHz high performance RLAN equipment National Authorities were informed according to Article 6.4 of Frequency Notification. Special Requirements are considered. The product is labeled with CE Marking.
[Hungarian] alapvetõ követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak. Polski [Polish] Niniejszym [nazwa producenta] oświadcza, że [nazwa wyrobu] jest zgodny z zasadniczymi wymogami oraz pozostałymi stosownymi postanowieniami Dyrektywy 1999/5/EC. Português [Nome do fabricante] declara que este [tipo de equipamento] está conforme [Portuguese com os requisitos essenciais e outras disposições da Directiva 1999/5/CE.
