Installation Guide

ManualsBrandsHOMESTYLES ManualsBathBarnside Metro 24 in. W x 60 in. H x 11 in. D Tagre in Driftwood Gray

Hardware List

Part List

Home Styles Customer Service: www.homestyles-furniture.com,

servicedesk@homestyles-furniture.com,

888-680-7460, 877-831-0319

Tool(s) required for assembly: Phillips screwdriver, Level, Drill (8 volts or less), 3/8” Drill Bit

88 5053 104

Seven Tier Shelf

IMPORTANT

Carefully remove all the parts from the carton and

place them individually on a soft cloth to prevent

scratches or other damage.

Carefully and strictly follow these assembly instructions

to ensure a completed product as designed.

Do not use power tools above 8 volts to assemble.

Top

1 pc.

Hex Wrench

1 pc.

Small Hex Wrench

1 pc.

M6x16

Head Cap Bolt

42 pcs. (+1 extra)

Spring Washer

42 pcs. (+1 extra)

Flat Washer

42 pcs. (+1 extra)

Shelf

4 pcs.

Shelf

2 pcs.

Side Frame

1 pc.

Side Frame

1 pc.

Stretcher

4 pcs.

Stretcher

2 pcs.

Adjustable Pin

16 pcs. (+1 extra)

Side Frame

1 pc.

Side Frame

1 pc.

Summary of content (5 pages)

PAGE 1
88 5053 104 Seven Tier Shelf IMPORTANT Carefully remove all the parts from the carton and place them individually on a soft cloth to prevent scratches or other damage. Carefully and strictly follow these assembly instructions to ensure a completed product as designed. Do not use power tools above 8 volts to assemble. Part List A. Top 1 pc. B. Shelf 4 pcs. D. Side Frame 1 pc. C. Shelf 2 pcs. E. Side Frame 1 pc. F. Side Frame 1 pc. G. Side Frame 1 pc. I. Stretcher 2 pcs. H. Stretcher 4 pcs.
PAGE 2
Assembly Instructions 2/4 IMPORTANT Use a soft cloth between these parts and the floor. Do not use power tools above 8 volts to assemble. Do not tighten all the bolts until each part is properly assembled. The unit must be level to work properly. Use the included adjustable levelers to level. Keep Hex Wrench in a safe place as the bolts may need to be tightened up in the future.
PAGE 3
Assembly Instructions 3/4 STEP 3 Attach Top (A) and Shelves (C) with Flat Washers, Spring Washers and Head Cap Bolts, tightening the bolts only half way. Tighten all Head Cap Bolts used in all steps. A C Flat Washer Spring Washer Head Cap Bolt C STEP 4 Adjustable Pin Turn unit to its’ upright position. Insert Adjustable Pins into unit at desired level. (See Figure 2) B Place Shelves (B) into position. B Level unit by adjusting the adjustable levelers on the bottom of unit.
PAGE 4
Assembly Instructions 4/4 IMPORTANT To help reduce the risk of the unit tipping over, the Tip-over Restraint must be installed following these instructions exactly. STEP 5 Anchor in wall Place unit at desired location. Bracket on wall Wall Screw 3/8” wall hole Pre-drilled hole at top of unit Machine Screw Drill a 3/8” hole in wall in-line with the pre-drilled hole at top of unit. Move unit. Tie end Insert Anchor into the wall hole and attach Bracket with Wall Screw.
PAGE 5
CARE INSTRUCTIONS NEVER NEVER use glass cleaners on finished furniture. Ammonia chemically attacks the finish. allow liquids to remain on furniture. Absorption causes parts to warp and split and finishes to delaminate. Do not use power tools above 8 volts to assemble. Do not place in direct sunlight. Do not write directly on surface. PREVENT CRACKING PREVENT FADING PREVENT MARKING Do not place hot objects on surface. Do not use rubber based placemats. Do not use commercial waxes and polishes.