Assembly Instructions Product Dimensions: 30.71”L×15.75”D×26.38”H Please take a moment to read through the entire instruction booklet before assembly to familiarize yourself with this product. Once you feel ready to start, follow the instructions step by step and this should make this process as easy as we could make it for you.
WARNING ! CAUTION ADULT ASSEMBLY REQUIRED CHOKING HAZARD • This product includes small parts, sharp points and sharp edges in its unassembled state. Keep unassembled parts away from children under 3 years of age, and animals. SAFETY WARNINGS • Follow the information on the warnings appearing on table and on the carton. Do not remove warning label from cabinet. • Do not allow children under 3 years of age to use the cabinet. • Do not use substitute parts.
ASSEMBLY AT A GLANCE Please take a moment to read through the whole instruction booklet before assembly to familiarize yourself with this product. Once you feel ready to start, follow the instructions step by step and this should make this process as easy as we could make it for you. 1 9 3 8 7 5 2 4 14 12 11 13 6 This drawing is to give you an overall idea only of how this assembly will go together and does not replace the assembly instructions.
COMPONENT PARTS Please check that you have all the parts listed below 1 1. Top Panel ×1 2. Left Side Panel×1 3. Right Side Panel×1 4. Bottom Panel×1 5. Support Side Panel×1 6. Front Door×1 7. Middle Support Panel×1 8. Left Back Side Panel×1 9. Right Back Side Panel×1 10. Drawer Front ×5 11. Drawer Bottom ×5 12. Drawer Back ×5 13. Drawer Left ×5 14.
ASSEMBLY INSTRUCTIONS 1 Select A×30 and 3×1, A A 7×1. Position 7 in the left, A A A position 3 in the right. Insert A A A A×5 into the one side of the A A B B, other A×5 into the middle A B A of the B, other A×5 into the B A B other side of the B.Insert B×5 A B into the 7.Repeat the steps A for the 3. A A A A A A A B A B B B B A A A 7 3 2 G Select 12×5,13×5,14×5, and G×20. Insert G×2 into the hole of the 13 into the 12.Repeat the steps for 14 and 12.
ASSEMBLY INSTRUCTIONS 3 Select 10×5 ,11×5 , D×10, E×10, F×10. Install the 11 along the grooves on the both sides of the 13 and 14. Install the 10 on the 13 with the D, E and F. Repeat the steps for the 10 and the 14. Repeat for another Drawer×4. 14 12 F D 11 13 E D F 10 E 4 A Select A × 30, C×2. Insert A×3 into the C into the 11 tightly. Repeat the steps for the other side of the 11.Repeat the steps for the other Drawer ×4.
ASSEMBLY INSTRUCTIONS 5 Select 2,5,7,D×4, E×4,F×2. Insert D×2 into the 2 into the two sides of the 5 with the F×2. Insert the E×2 into the 2 into the middle holes of the 5.Repeat for the 5 and the 7. 7 D E D D 5 F F E 2 F D 6 Select 2,3,4,5,7,E×6,G×6. Insert the 4 into the 2,the 7,the 3 with the E×6. Insert the G ×6 into the 4 into the 2,the 7 and the 3 tightly.
ASSEMBLY INSTRUCTIONS 7 1 Select the 1,the 2,the 3,the 8,the 9, D×6,E×6,F×6. Install the 8 along the grooves of the 2 and the 7.Repeat for the 9,the 3 and the 7. Insert the 1 into the 2,the 7,the 3 with the D×6,the E×6,the F×6. E D D D E D F 9 E D F F D 8 7 F F 3 F 2 8 Select the 4×1,the H×2, the I×2,the A×16. Put the cabinet upside down, insert the H×2 into the 4 with H the A×8 tightly. Repeat for the I×2.
ASSEMBLY INSTRUCTIONS 9 J Select the 6,J×4. Insert one of the K into the 6 with J×2.Repeat for the other K. K J K 6 J 10 K Insert the K×2 into the 6 and 2. Insert the J×8 into the hole of the K with the Phillips Screwdriver like picture.
ASSEMBLY INSTRUCTIONS 11 Put the Drawers ×5 into the Cabinet.
ASSEMBLY INSTRUCTIONS CONGRATULATIONS, YOUR OFFICECABINET IS COMPLETE! Page 11 of 11
