User Manual

HomeSeer | 10 Commerce Park North, Unit 10 | Bedford, NH 03110 | HomeSeer.com | Doc: HS-DS100-en-v1.0
HS-DS100+ Z-Wave Door / Window Sensor
Operaon
HS-DS100+ is comprised of a sensor body and a magnet piece. The sensor body is (typically) installed on a door or
window jamb. The magnet piece is (typically) installed on the door or window. When
the door or window are closed, the magnet trips a switch inside the sensor body and a
Z-Wave command is issued. When the door or window are opened, the switch is
tripped again and another Z-Wave command is issued.
Physical Installaon
The sensor body and magnet piece must be mounted to the door or window (vercally
or horizontally) using the provided screws or double-sck tape (your choice). Leave a
gap (no wider than 10mm) to allow the door or window to open and close easily with-
out obstrucon. If using screws, you’ll have to the mount the backing plates of the sensor body and magnet piec-
es rst. To do this, press the latch buon on the sensor body and gently pry o the backing plate. Then, use a
small sloed screwdriver to remove the backing plate from the magnet piece.
Z-Wave Network Installaon
Door/Window Sensor can be included and operated in any Z-Wave network with other Z-Wave cered devices from other manufacturers
and/or other applicaons. All non-baery operated nodes within the network will act as repeaters regardless of vendor to increase reliabil-
ity of the network.
Inclusion (Use this procedure to add the HS-DS100+ to your Z-Wave network).
1. Ensure AAA baeries are installed. Pull plasc tab from baery compartment (if necessary)
2. Put your home automaon controller into ‘inclusion’ mode. Consult your system’s manual for details.
3. HS-DS100+ may be included “securely” (opon a) or “non-securely” (opon b). If your automaon controller does not support secure de-
vices, or if you wish to improve baery life, add the sensor “non-securely”. Otherwise, include the sensor “securely”
a) Secure inclusion: Press and hold the Z-Wave buon inside the sensor body for 3 seconds. Wait for the process to nish.
b) Non-Secure inclusion: Triple-click the Z-Wave buon inside the sensor body. Wait for the process to nish.
4. If successful, the sensor body LED will blink briey and then stay on for 3 seconds. If unsuccessful, the LED with blink briey and then turn
o. Should this happen, repeat the inclusion process.
Note: If you want this Door/window sensor to funcon as a security device using secure/encrypted Z-Wave communicaons, then a secu-
rity enabled Z-Wave controller is required.
Exclusion (Use this procedure to remove the HS-DS100+ from your Z-Wave network).
1. Put your home automaon controller into ‘exclusion’ mode. Consult your system’s manual for details.
2. Triple-click the Z-Wave buon inside the sensor body. If successful, the LED will turn o within 1 second. If unsuccessful, the LED with
blink for 5 seconds. Should this happen, repeat the exclusion process.
Reset (Use this procedure to reset the HS-DS100+ to factory default sengs when the network primary controller is missing or otherwise
inoperable).
1. Press and hold the Z-Wave buon inside the sensor body for 20 seconds. If successful, the LED will change from solid, to blinking, to solid
again.
Z-Wave Associaon Informaon
HS-DS100+ supports Group 1 and Group 2 associaons. Group 1 reports the sensor’s condion, baery level and tamper state. Group 2
sends the BASIC SET command.
OVERVIEW
HS-DS100+ is a baery operated sensor that is designed to issue Z-Wave commands when doors or windows are opened or closed. HS-
DS100+ may be associated directly with other Z-Wave devices or it may be used with a wide variety of Z-Wave hubs and controllers to trig-
ger events, scenes and other automaons.