OPERATOR’S MANUAL Expand-it™ Tiller Attachment UT15550B Your Expand-it™ Tiller Attachment has been engineered and manufactured to a high standard for dependability, ease of operation, and operator safety. When properly cared for, it will give you years of rugged, trouble-free performance. WARNING: To reduce the risk of injury, the user must read and understand the operator’s manual before using this product. Thank you for buying an Expand-it™ product.
TABLE OF CONTENTS Introduction ................................................................................................................................................................... 2 General Safety Rules .................................................................................................................................................... 3 Specific Safety Rules ..............................................................................................................
GENERAL SAFETY RULES Inspect unit before each use for loose fasteners and damaged or missing parts. Correct before using the tiller attachment. Failure to do so can cause serious injury. WARNING: Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire, and/or serious personal injury. Use only original manufacturer’s replacement parts. Failure to do so may cause poor performance, possible injury, and will void your warranty.
SPECIFIC SAFETY RULES Rotating tines can cause severe injury, keep all body parts away from rotating tines. Be extremely careful when tilling in hard ground. The tines could catch in the ground and propel the tiller forward. Use extreme caution when reversing or pulling the machine towards you. Do not overload the capacity of the machine by attempting to till too deep at too fast a speed. Always be sure of your footing; keep a firm hold on the handles and walk; never run.
SYMBOLS Some of the following symbols may be used on this tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer. SYMBOL NAME EXPLANATION Safety Alert Symbol Precautions that involve your safety. Read The Operator’s Manual To reduce the risk of injury, user must read and understand operator’s manual before using this product. Eye and Hearing Protection Wear eye and hearing protection when operating this equipment.
FEATURES PRODUCT SPECIFICATIONS Weight ........................................................................................................................................................................13.5 lbs. END CAP “J” HANDLE TILLER ATTACHMENT SHAFT SHIELD TINES HANGER CAP GEAR BOX Fig. 1 KNOW YOUR TILLER ATTACHMENT See Figure 1.
ASSEMBLY UNPACKING This product has been shipped completely assembled. Carefully remove the items from the box. Make sure that all items listed in the packing list are included. Inspect the product carefully to make sure no breakage or damage occurred during shipping. Do not discard the packing material until you have carefully inspected and satisfactorily operated the tool. If any parts are damaged or missing, please call 1-800-242-4672 for assistance.
ASSEMBLY ATTACHING THE J-HANDLE See Figure 3. The J-handle included with the Expand-it™ Tiller Attachment provides a barrier to assist the operator in maintaining a safe distance from the rotating tines. If the power head to which the tiller attachment will be mounted does not have such a handle, install the provided handle. Hold the top and bottom clamp snugly in position on the shaft housing so that handle will be located to the operator’s left. FRONT HANDLE BOLT (1/4-20 x 1 in.
OPERATION WARNING: Keep hands and feet away from the rotating tines. Rotating tines will cause serious personal injury. NOTE: The tines of the tiller may rotate when the engine is started. Move the tiller to the work area before starting the engine. With the tiller on flat level ground, start the engine of the power head. Refer to the operator’s manual of your power head.
OPERATION REGULAR TINE PATTERN REGULAR TINE PATTERN See Figure 6. For most applications, the regular tine pattern will work best. This is the pattern set by the factory. NOTE: Pay attention to the hub position in relationship to the tines. HITCH PIN NARROW TINE PATTERN See Figure 7. When tilling in confined areas or rows, a narrow tine pattern may be required. For a narrow tine pattern: Remove hitch pin from each side of the tiller. Remove the left and right outer tines (A and D).
MAINTENANCE WARNING: When servicing, use only identical replacement parts. Use of any other parts may create a hazard or cause product damage. HANGER CAP WARNING: HOLE Always wear safety goggles or safety glasses with side shields during tool operation. If operation is dusty, also wear a dust mask.
EXPLODED VIEW AND PARTS LIST 5 14 16 15 4 3 13 2 19 20 19 20 13 6 17 21 22 1 8 9 12 18 10 11 7 12 12 7
EXPLODED VIEW AND PARTS LIST Key No. Part No. Description Qty. 1 220029002 Gear Case and Drive Shaft Assembly (Includes Key Nos. 2 and 17)................... 1 2 940657006 Warning Label ...................................................................................................... 1 3 308635001 Tine Shield Assembly (Includes Key Nos. 4 and 6) .............................................. 1 4 940627034 Expand-it Label ....................................................................
NOTES 14
WARRANTY LIMITED WARRANTY STATEMENT In addition, this warranty does not cover: A. Tune-ups – Spark Plugs, Carburetor, Carburetor Adjustments, Ignition, Filters B. Wear items – Bump Knobs, Outer Spools, Cutting Lines, Inner Reels, Starter Pulleys, Starter Ropes, Drive Belts, Tines, Felt Washers, Hitch Pins, Mulching Blades, Blower Fans, Blower and Vacuum Tubes, Vacuum Bags and Straps, Guide Bars, Saw Chains Techtronic Industries North America, Inc.
OPERATOR’S MANUAL Expand-it™ Tiller Attachment UT15550B SERVICE For parts or service, contact your nearest Expand-it™ authorized service center. Be sure to provide all relevant information when you call or visit. For the location of the authorized service center nearest you, please call 1-800-242-4672 or visit us online at www.homelite.com. REPAIR PARTS The model number of this tool is found on a plate or label attached to the housing. Please record the serial number in the space provided below.
