Base Cabinet Instruction Manual MODEL: B12-E B15-E B18-E B21-E I C DRAWER BACK PANEL A2 BOX SIDE PANEL - RIGHT G2 DRAWER SIDE PANEL - RIGHT BOX BACK PANEL G1 DRAWER SIDE PANEL - LEFT H DRAWER BOTTOM PANEL D A1 BOX SIDE PANEL - LEFT K ADJUSTABLE SHELF B FACE FRAME F DRAWER FACE PANEL J DOOR PANEL E TOE KICK PANEL BOX BOTTOM PANEL PART DESCRIPTION PART DESCRIPTION A1 A2 Box side panel - left Box side panel - right Box bottom panel G1 Drawer side panel - left Drawer side panel - rig
CAUTION Be sure to carefully remove all parts from the carton and ensure that there are no damages to any of them. The hardware should be kept away from children when unpacking and assembling this product. Two adults are recommended for assembly. Follow the instructions in the instruction manual carefully and strictly to ensure that the product is assembled and operates as intended. Do not tighten all the screws until all the adjacent parts have been properly connected.
CC Soft - close hinge x 2 Included: 1/2” Flat Head Phillips Screw x 4 Be careful the length of the screws.
INSTALLATION OVERVIEW 1 EE A1 Use 1/2” round head phillips screw x 10 2 EE A2 Use 1/2” round head phillips screw x 10 3b 3a C 3 C EE A2 A2 Use 1/2” round head phillips screw x 2 -3-
4a 4b Rotate EE A1 A1 A2 C A2 C Use 1/2” round head phillips screw x 2 5a 5 5b 5 B A1 A2 C 6a 6b D Inside EE D A2 A1 B A1 B A2 C C Use 1/2” round head phillips screw x 8 -4-
7a 7b E D Bottom E D A1 B A1 A2 EE A2 B EE C C Use 1/2” round head phillips screw x 12 8 Upright GG 9a AA A1 C B A2 D Use 5/8” flat head phillips screw x 4 -5-
9b AA A1 A2 C D B Use 5/8” flat head phillips screw x 4 10 11 G2 G2 F F G1 12a I 12b I G1 H H G1 G2 G2 F -6-
13a BB F G2 H I G1 Use 5/8” flat head phillips screw x 4 Be careful of the screw type. 13b F BB G2 H G1 I Use 3/8” flat head phillips screw x 4 Be careful of the screw type.
Insert the drawer on the extended runner. To secure the drawer clips with the runner, push the drawer in. Upon successful locking, a click can be heard. Ensure that the hook on each runner profile fits into the corresponding holes on the drawer back panel. 3 3 2 2 1 To level the drawer, use the green spur gears 1 to adjust drawer left and right, the green spur gears 2 to adjust drawer up and down, and the green spur gears 3 to adjust drawer inside and outside.
15b CC Use 3/4” flat head phillips screw x 2 Some products may have hinges pre-installed. To reverse the door, unscrew the 3/4" round head phillips screws from each hinge and remove the door panel. Then, reverse the door panel and drill the 3/4” round head phillips screws to each hinge through the pre-drilled holes to tighten the hinges with cabinet face frame.
17b a 17a a FF 18a 18b K 19 HH HH HH x6 20 HH Dear customers, Thank you for purchasing our product. If you require assistance, please contact the customer service team at the retailer where you purchased the product. The customer service team will be happy to assist you.
