Drawer Base Cabinet Instruction Manual MODEL: 3DB24-E G2 DRAWER SIDE PANEL - RIGHT I C DRAWER BACK PANEL A2 BOX SIDE PANEL - RIGHT BOX BACK PANEL D FACE FRAME F1 DRAWER FACE PANEL H DRAWER BOTTOM PANEL G1 DRAWER SIDE PANEL - LEFT A1 F2 DRAWER FACE PANEL E TOE KICK PANEL BOX SIDE PANEL - LEFT B BOX BOTTOM PANEL PART DESCRIPTION PART DESCRIPTION A1 A2 Box side panel - left Box side panel - right Box bottom panel F1 F2 G1 Box back panel Face frame Toe kick panel G2 H I Drawer face pane
CAUTION Be sure to carefully remove all parts from the carton and ensure that there are no damages to any of them. The hardware should be kept away from children when unpacking and assembling this product. Two adults are recommended for assembly. Follow the instructions in the instruction manual carefully and strictly to ensure that the product is assembled and operates as intended. Do not tighten all the screws until all the adjacent parts have been properly connected.
DD Wood corner block x 4 Included: 1” Flat Head Phillips Screw x 8 EE Corner brace x 13 Included: 1/2” Round Head Phillips Screw x 52 GG 1” Flat head Phillips screw x 3 HH Rubber bumper x 12 TOOLS REQUIRED (NOT INCLUDED) -2-
INSTALLATION OVERVIEW 1 EE A1 Use 1/2” round head phillips screw x 10 2 EE A2 Use 1/2” round head phillips screw x 10 3b 3a C 3 C EE A2 A2 Use 1/2” round head phillips screw x 2 -3-
4a 4b Rotate EE A1 A1 A2 C A2 C Use 1/2” round head phillips screw x 2 5a 5 5b 5 B A1 A2 C 6a 6b D Inside EE D A1 A2 B A2 B A1 C C Use 1/2” round head phillips screw x 8 -4-
7a 7b E D Bottom E D A1 A1 A2 B EE B A2 EE C C Use 1/2” round head phillips screw x 20 8 Upright GG 9a AA A1 C A2 D B Use 5/8” flat head phillips screw x 12 -5-
9b AA C A1 A2 D B Use 5/8” flat head phillips screw x 12 10 11 G2 G2 F1 F1 G1 12 13 I I H G1 G1 H G2 G2 F1 -6-
14a 14b F2 F2 15a BB F1 G2 H I G1 Use 5/8” flat head phillips screw x 4 Be careful of the screw type. 15b F1 BB G2 H G1 x2 I Use 3/8” flat head phillips screw x 4 Be careful of the screw type.
16 17 Insert the drawer on the extended runner. To secure the drawer clips with the runner, push the drawer in. Upon successful locking, a click can be heard. Ensure that the hook on each runner profile fits into the corresponding holes on the drawer back panel. 3 3 2 2 1 To level the drawer, use the green spur gears 1 to adjust drawer left and right, the green spur gears 2 to adjust drawer up and down, and the green spur gears 3 to adjust drawer inside and outside.
18a a 18b a DD x4 DD Use 1” flat head phillips screw x 8 (2 screws for 1 corner block) 19 HH HH HH x12 20 HH Dear customers, Thank you for purchasing our product. If you require assistance, please contact the customer service team at the retailer where you purchased the product. The customer service team will be happy to assist you.
