Installation Guide

ManualsBrandsHome2O ManualsBathroom Sink FaucetsSivan Brushed Nickel 2-handle 4-in Centerset WaterSense Bathroom Sink Faucet with Drain

Homewerks Worldwide, LLC • Lake Bluff, IL 60044 • www.homewerksww.com

BATHROOM FAUCET

H11L-421-CH – Polished chrome nish with pop-up

H11L-421-BN – Brushed nickel nish with pop-up

H11L-421-MB – Matte black nish with pop-up

PACKAGE AND HARDWARE CONTENTS

NSF/ANSI-61

ADA

PART DESCRIPTION

QUANTITY

A Faucet assembly 1

B Push pop-up assembly 1

C Mounting nut 2

SAFETY INFORMATION

Please read and understand this entire manual before attempting to assemble,

operate or install the product.

WARNING

• Protect your eyes with safety glasses when cutting or soldering water

supply lines.

CAUTION

• If you solder the joints during installation, the seats, cartridges, and washers

must be removed before using a ame or the warranty will be voided on

these parts.

• Cover the drain to avoid losing parts.

PREPARATION

Before beginning assembly of product, make sure all parts are present. Compare

parts with package contents list and hardware contents. If any part is missing or

damaged, do not attempt to assemble the product.

Contact customer service for replacement parts.

Estimated Assembly Time: 30 minutes

Tools Required for Assembly (not included): Adjustable wrench, thread sealant tape,

silicone

Installations may vary depending on how the previous faucet was installed. Supplies

necessary for the installation of the faucet are not all included; however, they

are available wherever plumbing supplies are sold.

Prior to beginning installation, turn off the hot and cold water lines, then turn

on the old faucet to release built-up pressure. When installing the new faucet,

hand tighten the connector nuts. DO NOT OVERTIGHTEN. Connections

that are too tight will reduce the integrity of the system.

Need Help? Please call our toll-free line at (877) 319-3757 (8 am to 5 pm CST) for additional assistance or service.

02-02-2018

Summary of content (8 pages)

PAGE 1
BATHROOM FAUCET H11L-421-CH – Polished chrome finish with pop-up H11L-421-BN – Brushed nickel finish with pop-up H11L-421-MB – Matte black finish with pop-up NSF/ANSI-61 PACKAGE AND HARDWARE CONTENTS ADA DESCRIPTION QUANTITY A Faucet assembly 1 B Push pop-up assembly 1 C Mounting nut 2 PART B A C SAFETY INFORMATION Please read and understand this entire manual before attempting to assemble, operate or install the product.
PAGE 2
PRODUCT SPECIFICATIONS SPECIFICATIONS SPECIFICATIONS Max. Flow Rate: 1.2 GPM (4.5 LPM) at 60 PSI Ceramic cartridges ASME A112.18.1/CSA B125 NSF 61-9 Manufactured to include no more than 0.25% weighted average lead content on wetted surfaces Polished chrome, brushed nickel or matte black finish Total weight of item: 2.84 lbs. 1. urn off water at the supply valve T under the sink or at the main water supply, disconnect the supply line, and remove old faucet. 5.
PAGE 3
TROUBLESHOOTING PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION Leaks underneath handle. Bonnet has come loose or O-ring on cartridge is dirty or twisted. 1. M ove the handle to the OFF position. Unscrew the handle screw and remove the handle. 2. Tighten the bonnet by turning it clockwise. Move the cartridge stem to the on position. The leak should stop draining out from around the cartridge stem. 3. S hut off the water supply. Remove the bonnet by turning it counterclockwise.
PAGE 4
REPLACEMENT PARTS For replacement parts, call our customer service department at (866) 459-3757, 8 a.m. - 5 p.m., CST, Monday - Friday.
PAGE 5
GRIFO PARA BAÑO H11L-421-CH – Acabado de cromo pulido con pop-up H11L-421-BN – Acabado niquel pulido con pop-up H11L-421-MB – Acabado negro mate con pop-up NSF/ANSI-61 PAQUETE DE HARDWARE Y CONTENIDO ADA PARTE DESCRIPCIÓN CANTIDAD A Montaje de grifería 1 B Ensamblaje emergente 1 C Tuerca de montaje 2 B A C INFORMACIÓN SOBRE LA SEGURIDAD Por favor, lea y comprenda la totalidad de este manual antes de intentar armado, manejo o instalación del producto.
PAGE 6
ESPECIFICACIONES DEL PRODUCTO ESPECIFICACIONES ESPECIFICACIONES Max. Caudal: 1,2 GPM (4.54 LPM) a 60 PSI Cartuchos sin arandela ASME A112.18.1/CSA B125 NSF 61-9 Fabricado a incluir no más de 0,25% de contenido de plomo promedio ponderado en superficies mojadas Acabado en cromo pulido, níquel cepillado o negro mate. Peso total del material: 2,84 libras.
PAGE 7
SOLUCIÓN DE PROBLEMAS PROBLEMA POSIBLE CAUSA ACCIÓN CORRECTIVA Fugas debajo de manejar. El capuchón se aflojó o la junta tórica en el cartucho está sucia o doblada. 1. Mover la palanca a la posición OFF. Afloje el tornillo de la manija y retire la manija. 2. Apriete el capó girando en sentido horario. Mueva el vástago del cartucho a la posición de encendido. La fuga debe dejar de escape hacia afuera de todo el vástago del cartucho. 3. C ierre el suministro de agua.
PAGE 8
LISTA DE REPUESTOS Para piezas de repuesto, llame a nuestro departamento de servicio al cliente al (866) 459-3757, 8 a.m.-5 p.m. CST, Lunes - Viernes.