- HAI OmniPro II Owner's Manual
Table Of Contents
- INTRODUCTION
- OVERALL DESCRIPTION
- SECURITY SYSTEM OPERATION
- Disarming the Security System and Silencing Alarms
- Arming the Security System
- Using Shortcut Keys
- Quick Arm
- Bypassing Zones
- Restoring Zones
- What To Do When You Come Home
- What Happens When the Alarm is Activated
- Emergency Keys
- Duress Code Entered or Duress Alarm Activated
- Alarm Reset
- Alarm Cancel
- Trouble Indications
- Codes
- Duress Code
- Panic Switches
- Area Arming
- GOTO Area
- Testing Your System
- CONTROL
- Control Commands
- About UPB
- HAI Lighting Control (HLC) Format
- About CentraLite
- About Lutron RadioRA
- About ALC
- About X-10
- House Codes
- Unit Numbers
- Scrolling Through Names
- Controlling Units
- Timed Commands
- Status of a Unit
- Internal Flags
- Controlling Outputs
- All On / Off
- Leviton Scene Control
- Buttons
- Temperature Control
- HAI RC-Series Thermostats
- Programmable Energy Saver Modules (PESMs)
- Temperature Alarms
- Humidity
- Status
- Event Log
- Messages
- TELEPHONE CONTROL
- Telephone Interface
- In-House Phones
- Remote Phones
- Phone Access Denied - Remote Lockout
- Alternate Method
- Main Menu
- 1 - Control
- 2 - Security
- 3 - Button
- 4 - All
- 5 - Temperature
- 6 - Status
- 7 - Events
- 8 - Message
- 9 - Good-Bye
- Panic Button over the Phone (# # # # # #)
- Emergency Dial-Out
- Digital Dialer
- Voice Dialer
- PC Access
- Built-In Ethernet Port
- Controller IP Address, Port Number, and Encryption Key
- OmniPro II Ethernet Connections
- Connecting to Network via PC Access
- Dynamic DNS
- SETUP
- UNDERWRITER'S LABORATORIES REQUIREMENTS
- FEDERAL COMMUNICATION COMMISSION NOTICE:
- CANADIAN INDUSTRY CANADA NOTICE
- APPENDIX A - DIAL OUT PLANNER
- APPENDIX B - TEXT DESCRIPTION CHARACTER CODES
- APPENDIX C - VOICE DESCRIPTION CODES
Program Video Commands*
This program command is used to display video automatically on an OmniTouch with Video touchscreen when an event occurs.
You can specify which camera and which touchscreen(s) will display the video when the event takes place. When the event takes
place, it switches each of the specified touchscreens to full screen video.
* This item can only be programmed via PC Access.
Program Temperature Commands
Select the 5 (TEMP) key to control HAI Communicating Thermostats, energy saver modules, and temperature sensors. Specify
the desired command - See Temperature.
TEMPERATURE:
ENTER TEMP ZONE 0=ALL
↓
Program Energy Cost
Select the 6 (ENERGY) key to command the energy cost rate. Specify the desired energy cost rate:
ENERGY COST:
0=LO 1=MID 2=HI 3=CRIT
Program Message Commands
Select the 8 (MESSAGE) key to show, log, clear, say, phone, or send a message. Specify the desired command - See Message.
MESSAGE
1=SHOW 2=LOG 3=CLEAR
↓
4=SAY 5=PHONE 6=SEND
↑
The 1 (SHOW) key allows you to display the selected text message(s) on the console's top-level display. This can be a helpful
reminder of special events and occasions.
The 2 (LOG) key allows you to store the selected text message(s) in the Event Log. This can be a helpful to keep track of the
times and dates of events and occurrences.
The 3 (CLEAR) key allows you to clear the selected text message, or all text messages from the console's display.
The 4 (SAY) key allows the controller to say the selected voice message over a speaker. This voice message can be an audible
reminder of special events and occasions (i.e. "Front Door Open" when the front door is opened).
The 5 (PHONE) key allows the controller to call the selected phone number and say the selected voice message.
The 4 (SEND) key allows you to send any a text messages through the Pro-Link serial port.
Page 68