- HAI OmniPro II Owner's Manual
Table Of Contents
- INTRODUCTION
- OVERALL DESCRIPTION
- SECURITY SYSTEM OPERATION
- Disarming the Security System and Silencing Alarms
- Arming the Security System
- Using Shortcut Keys
- Quick Arm
- Bypassing Zones
- Restoring Zones
- What To Do When You Come Home
- What Happens When the Alarm is Activated
- Emergency Keys
- Duress Code Entered or Duress Alarm Activated
- Alarm Reset
- Alarm Cancel
- Trouble Indications
- Codes
- Duress Code
- Panic Switches
- Area Arming
- GOTO Area
- Testing Your System
- CONTROL
- Control Commands
- About UPB
- HAI Lighting Control (HLC) Format
- About CentraLite
- About Lutron RadioRA
- About ALC
- About X-10
- House Codes
- Unit Numbers
- Scrolling Through Names
- Controlling Units
- Timed Commands
- Status of a Unit
- Internal Flags
- Controlling Outputs
- All On / Off
- Leviton Scene Control
- Buttons
- Temperature Control
- HAI RC-Series Thermostats
- Programmable Energy Saver Modules (PESMs)
- Temperature Alarms
- Humidity
- Status
- Event Log
- Messages
- TELEPHONE CONTROL
- Telephone Interface
- In-House Phones
- Remote Phones
- Phone Access Denied - Remote Lockout
- Alternate Method
- Main Menu
- 1 - Control
- 2 - Security
- 3 - Button
- 4 - All
- 5 - Temperature
- 6 - Status
- 7 - Events
- 8 - Message
- 9 - Good-Bye
- Panic Button over the Phone (# # # # # #)
- Emergency Dial-Out
- Digital Dialer
- Voice Dialer
- PC Access
- Built-In Ethernet Port
- Controller IP Address, Port Number, and Encryption Key
- OmniPro II Ethernet Connections
- Connecting to Network via PC Access
- Dynamic DNS
- SETUP
- UNDERWRITER'S LABORATORIES REQUIREMENTS
- FEDERAL COMMUNICATION COMMISSION NOTICE:
- CANADIAN INDUSTRY CANADA NOTICE
- APPENDIX A - DIAL OUT PLANNER
- APPENDIX B - TEXT DESCRIPTION CHARACTER CODES
- APPENDIX C - VOICE DESCRIPTION CODES
To play one of the custom phrases, press the 6 key.
" PLAY PHRASE: ENTER PHRASE NUMBER, THEN POUND."
Press the phrase number (1-60) you wish to play, then press #.
"PHRASE IS: (OMNIPRO II PLAYS PHRASE)."
To record one of the custom phrases, press the 7 key.
" RECORD PHRASE: ENTER PHRASE NUMBER, THEN POUND."
Press the phrase number (1-60) you wish to record, then press #.
"RECORD PHRASE - [BEEP]"
At the [BEEP], record your custom phrase…
At the second [BEEP]:
"PHRASE IS: (OMNIPRO II PLAYS PHRASE)."
Playing and Recording the Address
To record the address, press the 9 key and enter the Master code.
"RECORD ADDRESS - [BEEP]
At the [BEEP], record your name and address.
"ADDRESS IS: (OMNIPRO II PLAYS ADDRESS)."
Note: The address is used only for the VOICE dial out feature.
9 - Good-Bye
Press 9 from the MAIN MENU.
The OmniPro II will say, "GOOD-BYE" and hang up.
From an in-house phone, the dial tone will return. From a remote phone, you will hear a click as the OmniPro II hangs up. It is
recommended that you press 9 to terminate a remote call. If you don't, the OmniPro II will hang up anyway after about 15
seconds.
Panic Button over the Phone (# # # # # #)
On an in-house phone only, you can activate the Police Emergency keys by picking up the phone and pressing the # key 6 times.
This activates the sounder immediately.
The first # that you press logs you in, as usual, then the next 5 presses of the # key activate the alarm. If you are already logged
into your system, then it takes only 5 presses of the # key to activate the emergency alarm. To prevent accidental activation of the
panic feature over the phone, you must press the # key 5 times, all at once. If you pause for more than 2 seconds, or press any
other key, the panic activation is canceled. The OmniPro II will say "CANCEL".
Note that the Panic Button over the Phone feature only works if you are logged into the system. In an emergency, if you wish to
set off the alarm, simply pick up the phone and repeatedly press the # key until the alarm sounds. Be aware that, under some
circumstances, it may be smarter to dial 911 or your police department directly. Also be aware that your telephone will be
unusable while the OmniPro II dials out.
Page 49