- HAI OmniPro II Owner's Manual
Table Of Contents
- INTRODUCTION
- OVERALL DESCRIPTION
- SECURITY SYSTEM OPERATION
- Disarming the Security System and Silencing Alarms
- Arming the Security System
- Using Shortcut Keys
- Quick Arm
- Bypassing Zones
- Restoring Zones
- What To Do When You Come Home
- What Happens When the Alarm is Activated
- Emergency Keys
- Duress Code Entered or Duress Alarm Activated
- Alarm Reset
- Alarm Cancel
- Trouble Indications
- Codes
- Duress Code
- Panic Switches
- Area Arming
- GOTO Area
- Testing Your System
- CONTROL
- Control Commands
- About UPB
- HAI Lighting Control (HLC) Format
- About CentraLite
- About Lutron RadioRA
- About ALC
- About X-10
- House Codes
- Unit Numbers
- Scrolling Through Names
- Controlling Units
- Timed Commands
- Status of a Unit
- Internal Flags
- Controlling Outputs
- All On / Off
- Leviton Scene Control
- Buttons
- Temperature Control
- HAI RC-Series Thermostats
- Programmable Energy Saver Modules (PESMs)
- Temperature Alarms
- Humidity
- Status
- Event Log
- Messages
- TELEPHONE CONTROL
- Telephone Interface
- In-House Phones
- Remote Phones
- Phone Access Denied - Remote Lockout
- Alternate Method
- Main Menu
- 1 - Control
- 2 - Security
- 3 - Button
- 4 - All
- 5 - Temperature
- 6 - Status
- 7 - Events
- 8 - Message
- 9 - Good-Bye
- Panic Button over the Phone (# # # # # #)
- Emergency Dial-Out
- Digital Dialer
- Voice Dialer
- PC Access
- Built-In Ethernet Port
- Controller IP Address, Port Number, and Encryption Key
- OmniPro II Ethernet Connections
- Connecting to Network via PC Access
- Dynamic DNS
- SETUP
- UNDERWRITER'S LABORATORIES REQUIREMENTS
- FEDERAL COMMUNICATION COMMISSION NOTICE:
- CANADIAN INDUSTRY CANADA NOTICE
- APPENDIX A - DIAL OUT PLANNER
- APPENDIX B - TEXT DESCRIPTION CHARACTER CODES
- APPENDIX C - VOICE DESCRIPTION CODES
Press the temperature zone you wish to control, then press #.
Press the ' 0 ' key to select all HAI Thermostats. This is a simple way to broadcast the new Heat or Cool setting or change the
system mode, fan mode, or hold mode of all HAI thermostats in your system.
When an HAI Communicating Thermostat is entered:
"THERMOSTAT 1 - THERMOSTAT 1 - TEMPERATURE IS (TEMP)."
"PLEASE CHOOSE:
1: MODE
2: HEAT SETTING
3: COOL SETTING
4: FAN
5: HOLD
#: STATUS
*: CANCEL
- If the # (STATUS) key is selected, OmniPro II will read the current status of the thermostat. For instance:
"TEMPERATURE IS (80), HEAT SETTING IS (60), COOL SETTING IS (75),
MODE IS (COOL), FAN IS (AUTO), HOLD IS (OFF)."
When a Programmable Energy Saver (PESM) is entered:
"ZONE 9 ENERGY SAVER - ENERGY SAVER IS (ON/OFF).
TEMPERATURE IS (TEMP)."
"PLEASE CHOOSE:
0: OFF
1: ON
2: HEAT SETTING
3: COOL SETTING
9: TIMED
#: STATUS
*: CANCEL
- If the # (STATUS) key is selected, OmniPro II will read the current status of the PESM. For instance:
"ENERGY SAVER IS (ON/OFF): TEMPERATURE IS (80), HEAT SETTING IS (60), COOL SETTING IS (75)."
6 - Status
Press 6 from the MAIN MENU to get to the STATUS menu.
From the Status menu, OmniPro II will report the Security Mode (for the current Area).
If all zones are secure and there are no troubles with the system, OmniPro II reports "System OK".
If any zones are currently not ready, in trouble, or bypassed, OmniPro II will report the current status of those zones. Any system
troubles are also reported.
Finally, OmniPro II will report the current Outdoor Temperature (if part of the system) and the current time and date.
7 - Events
Press 7 from the MAIN MENU to get to the EVENT menu.
The OmniPro II will read the 3 latest events. Press the ' 7 ' key for OmniPro II to read 3 more events, or ' * ' to cancel.
Page 47