- HAI OmniPro II Owner's Manual
Table Of Contents
- INTRODUCTION
- OVERALL DESCRIPTION
- SECURITY SYSTEM OPERATION
- Disarming the Security System and Silencing Alarms
- Arming the Security System
- Using Shortcut Keys
- Quick Arm
- Bypassing Zones
- Restoring Zones
- What To Do When You Come Home
- What Happens When the Alarm is Activated
- Emergency Keys
- Duress Code Entered or Duress Alarm Activated
- Alarm Reset
- Alarm Cancel
- Trouble Indications
- Codes
- Duress Code
- Panic Switches
- Area Arming
- GOTO Area
- Testing Your System
- CONTROL
- Control Commands
- About UPB
- HAI Lighting Control (HLC) Format
- About CentraLite
- About Lutron RadioRA
- About ALC
- About X-10
- House Codes
- Unit Numbers
- Scrolling Through Names
- Controlling Units
- Timed Commands
- Status of a Unit
- Internal Flags
- Controlling Outputs
- All On / Off
- Leviton Scene Control
- Buttons
- Temperature Control
- HAI RC-Series Thermostats
- Programmable Energy Saver Modules (PESMs)
- Temperature Alarms
- Humidity
- Status
- Event Log
- Messages
- TELEPHONE CONTROL
- Telephone Interface
- In-House Phones
- Remote Phones
- Phone Access Denied - Remote Lockout
- Alternate Method
- Main Menu
- 1 - Control
- 2 - Security
- 3 - Button
- 4 - All
- 5 - Temperature
- 6 - Status
- 7 - Events
- 8 - Message
- 9 - Good-Bye
- Panic Button over the Phone (# # # # # #)
- Emergency Dial-Out
- Digital Dialer
- Voice Dialer
- PC Access
- Built-In Ethernet Port
- Controller IP Address, Port Number, and Encryption Key
- OmniPro II Ethernet Connections
- Connecting to Network via PC Access
- Dynamic DNS
- SETUP
- UNDERWRITER'S LABORATORIES REQUIREMENTS
- FEDERAL COMMUNICATION COMMISSION NOTICE:
- CANADIAN INDUSTRY CANADA NOTICE
- APPENDIX A - DIAL OUT PLANNER
- APPENDIX B - TEXT DESCRIPTION CHARACTER CODES
- APPENDIX C - VOICE DESCRIPTION CODES
1 - Control
Press 1 from the MAIN MENU to get to the CONTROL menu.
If voice descriptions have been programmed, after a three-second delay, the system will begin reading from the list of units
(OmniPro II will say the unit number then its description). The OmniPro II will read three units, then say,
"PRESS POUND TO CONTINUE."
If the ' # ' key is pressed, OmniPro II will read the next three unit numbers and descriptions (if programmed).
2 - Security
Press 2 from the MAIN MENU to get to the SECURITY menu.
From the Security menu you can arm your system (Day, Night, Away, Vacation, Day Instant, and Night Delayed), disarm you
system, bypass and restore zones, and go to a different area.
When bypassing and restoring a zone, if voice descriptions have been programmed, after a three-second delay, the system will
begin reading from the list of zones. If the ' # ' key is pressed, OmniPro II will read the next three descriptions (if programmed).
GOTO Area
Press the # key to GOTO a different area. OmniPro II will say:
"GOTO AREA: ENTER AREA THEN #." "ENTER CODE, *: CANCEL"
"WELCOME TO OMNIPRO II, AREA 2."
3 - Button
Press 3 from the MAIN MENU to get to the BUTTON menu.
If button voice descriptions have been programmed, after a three-second delay, the system will begin reading from the list of
buttons (OmniPro II will say the button number then its description).
User buttons 1 - 128 are available from the phone, for the current area.
4 - All
Press 4 from the MAIN MENU to get to the ALL menu.
"ALL: PLEASE CHOOSE:"
0: ALL OFF
1: ALL ON
2: LIGHT SETTING (Leviton Scene)
5 - Temperature
Press 5 from the MAIN MENU to get to the TEMPERATURE menu. The OmniPro II will say,
"TEMPERATURE: ENTER TEMPERATURE NUMBER, THEN POUND."
After a three second delay, the system will begin reading from the list of Thermostats and Energy Savers (if voice descriptions
have been programmed, OmniPro II will say the temperature zone then its description). The OmniPro II will read three
temperature zones, then say,
"PRESS POUND TO CONTINUE."
If the ' # ' key is pressed, OmniPro II will read the next three temperature zones and descriptions (if programmed).
Page 46