- HAI OmniPro II Owner's Manual
Table Of Contents
- INTRODUCTION
- OVERALL DESCRIPTION
- SECURITY SYSTEM OPERATION
- Disarming the Security System and Silencing Alarms
- Arming the Security System
- Using Shortcut Keys
- Quick Arm
- Bypassing Zones
- Restoring Zones
- What To Do When You Come Home
- What Happens When the Alarm is Activated
- Emergency Keys
- Duress Code Entered or Duress Alarm Activated
- Alarm Reset
- Alarm Cancel
- Trouble Indications
- Codes
- Duress Code
- Panic Switches
- Area Arming
- GOTO Area
- Testing Your System
- CONTROL
- Control Commands
- About UPB
- HAI Lighting Control (HLC) Format
- About CentraLite
- About Lutron RadioRA
- About ALC
- About X-10
- House Codes
- Unit Numbers
- Scrolling Through Names
- Controlling Units
- Timed Commands
- Status of a Unit
- Internal Flags
- Controlling Outputs
- All On / Off
- Leviton Scene Control
- Buttons
- Temperature Control
- HAI RC-Series Thermostats
- Programmable Energy Saver Modules (PESMs)
- Temperature Alarms
- Humidity
- Status
- Event Log
- Messages
- TELEPHONE CONTROL
- Telephone Interface
- In-House Phones
- Remote Phones
- Phone Access Denied - Remote Lockout
- Alternate Method
- Main Menu
- 1 - Control
- 2 - Security
- 3 - Button
- 4 - All
- 5 - Temperature
- 6 - Status
- 7 - Events
- 8 - Message
- 9 - Good-Bye
- Panic Button over the Phone (# # # # # #)
- Emergency Dial-Out
- Digital Dialer
- Voice Dialer
- PC Access
- Built-In Ethernet Port
- Controller IP Address, Port Number, and Encryption Key
- OmniPro II Ethernet Connections
- Connecting to Network via PC Access
- Dynamic DNS
- SETUP
- UNDERWRITER'S LABORATORIES REQUIREMENTS
- FEDERAL COMMUNICATION COMMISSION NOTICE:
- CANADIAN INDUSTRY CANADA NOTICE
- APPENDIX A - DIAL OUT PLANNER
- APPENDIX B - TEXT DESCRIPTION CHARACTER CODES
- APPENDIX C - VOICE DESCRIPTION CODES
Messages
The Message menu is used to play and record the memo message and to quickly clear all text messages. The memo message is an
eight-second voice message. It's like an "electronic notepad" for a family member to leave a handy message. After a message is
recorded, it can automatically be played back when someone returns and disarms the security system.
The Message menu is also used to show, log, clear, and send text messages, and to say and phone (dial out) your voice messages.
To enter the Message menu, from the top-level display or from the main menu, press the 8 (MESSAGE) key on the console.
MESSAGE
1=PLAY 2=RECORD 3=CLEAR
8=MESSAGE
↑
Record Memo Message
Note: To Record the memo message using this key, the HAI Two-Way Audio Module (with a microphone) must be installed.
To record a new voice memo message, press the 2 (RECORD) key.
OmniPro II will say, "Record Message". At the beep, record your eight-second message. OmniPro II will beep a second time at
the end of the eight seconds, which signifies the end of the record process.
After a new message is recorded, the display will show "CHECK MESSAGE".
Play Memo Message
Note: To Play the memo message using this key, the HAI Two-Way Audio Module (with a speaker) must be installed.
To play the voice message, press the 1 (PLAY) key.
Over the speaker, OmniPro II will say, "Message is" - OmniPro II will then play your eight-second message.
• OmniPro II will automatically play a new memo message when the security system is disarmed.
• After the message has been played, the display will no longer show "CHECK MESSAGE".
Clear Text Messages
If any text messages are currently being displayed on the console, they can be deleted by pressing the 3 (CLEAR) key.
When you press the 3 (CLEAR) key, all messages are cleared from the console display.
Message
To show, log, clear, and send text messages, and to say and phone (dial out) your voice messages, press the 8 (MESSAGE) key:
MESSAGE
1=SHOW 2=LOG 3=CLEAR
↓
4=SAY 5=PHONE 6=SEND
↑
Page 41