- HAI OmniPro II Owner's Manual
Table Of Contents
- INTRODUCTION
- OVERALL DESCRIPTION
- SECURITY SYSTEM OPERATION
- Disarming the Security System and Silencing Alarms
- Arming the Security System
- Using Shortcut Keys
- Quick Arm
- Bypassing Zones
- Restoring Zones
- What To Do When You Come Home
- What Happens When the Alarm is Activated
- Emergency Keys
- Duress Code Entered or Duress Alarm Activated
- Alarm Reset
- Alarm Cancel
- Trouble Indications
- Codes
- Duress Code
- Panic Switches
- Area Arming
- GOTO Area
- Testing Your System
- CONTROL
- Control Commands
- About UPB
- HAI Lighting Control (HLC) Format
- About CentraLite
- About Lutron RadioRA
- About ALC
- About X-10
- House Codes
- Unit Numbers
- Scrolling Through Names
- Controlling Units
- Timed Commands
- Status of a Unit
- Internal Flags
- Controlling Outputs
- All On / Off
- Leviton Scene Control
- Buttons
- Temperature Control
- HAI RC-Series Thermostats
- Programmable Energy Saver Modules (PESMs)
- Temperature Alarms
- Humidity
- Status
- Event Log
- Messages
- TELEPHONE CONTROL
- Telephone Interface
- In-House Phones
- Remote Phones
- Phone Access Denied - Remote Lockout
- Alternate Method
- Main Menu
- 1 - Control
- 2 - Security
- 3 - Button
- 4 - All
- 5 - Temperature
- 6 - Status
- 7 - Events
- 8 - Message
- 9 - Good-Bye
- Panic Button over the Phone (# # # # # #)
- Emergency Dial-Out
- Digital Dialer
- Voice Dialer
- PC Access
- Built-In Ethernet Port
- Controller IP Address, Port Number, and Encryption Key
- OmniPro II Ethernet Connections
- Connecting to Network via PC Access
- Dynamic DNS
- SETUP
- UNDERWRITER'S LABORATORIES REQUIREMENTS
- FEDERAL COMMUNICATION COMMISSION NOTICE:
- CANADIAN INDUSTRY CANADA NOTICE
- APPENDIX A - DIAL OUT PLANNER
- APPENDIX B - TEXT DESCRIPTION CHARACTER CODES
- APPENDIX C - VOICE DESCRIPTION CODES
HAI RC-Series Thermostats
The following control actions are allowed for HAI Communicating Thermostats:
•
Set heating setpoints
• Set cooling setpoints
• Set system mode (Off / Heat / Cool / Auto)
• Set fan (On / Auto)
• Turn hold On and Off
NOTE: Not all actions are applicable to every type of thermostat.
To enter the temperature menu, from the top-level display or from the main menu, press the 5 (TEMP) key on the console keypad.
You will be prompted with the first named temperature zone (i.e. Upstairs). The temperature zone can be specified by entering
the temperature zone number followed by the ' # ' key, or by pressing the arrow keys to scroll through the list of temperature
zones. Press the ' # ' key when the desired temperature zone is shown.
Press the ' 0 ' key to select all HAI Thermostats. This is a simple way to broadcast the new Heat or Cool setting or change the
system mode, fan mode, or hold mode of all HAI thermostats in your system. Temperature zones 1-64 are for HAI thermostats.
TEMPERATURE:
ENTER TEMP ZONE 0=ALL
↓
After the ' # ' key is pressed, a menu appropriate for the type of temperature zone is shown. For Celsius temperatures, press the
' # ' key prior to entering the temperature to make the number negative. The Celsius temperature may also be specified in 0.5
degree steps, if three numeric digits are entered. The third digit adds a .5 to the first two digits, if it is anything other than zero.
Enter a leading zero, if necessary.
For HAI heat/cool thermostats:
Upstairs
1=MODE 2=HEAT 3=COOL
↓
Upstairs
4=FAN 5=HOLD #=STAT
↑
To change the system mode on a thermostat, press 1 (MODE). A menu presenting options appropriate for that type of thermostat
is then displayed. For heat/cool thermostats with auto changeover:
Upstairs MODE
0=OFF 1=HEAT 2=COOL ↓
Upstairs MODE
3=AUTO
↑
To change a temperature setting, press 2 (HEAT), 3 (COOL), or 2 (TEMP) as appropriate:
Upstairs HEAT
ENTER TEMPERATURE:
Upstairs COOL
ENTER TEMPERATURE:
Upstairs TEMP
ENTER TEMPERATURE:
Enter the desired temperature then press the ' # ' key.
Page 31