- HAI OmniPro II Owner's Manual
Table Of Contents
- INTRODUCTION
- OVERALL DESCRIPTION
- SECURITY SYSTEM OPERATION
- Disarming the Security System and Silencing Alarms
- Arming the Security System
- Using Shortcut Keys
- Quick Arm
- Bypassing Zones
- Restoring Zones
- What To Do When You Come Home
- What Happens When the Alarm is Activated
- Emergency Keys
- Duress Code Entered or Duress Alarm Activated
- Alarm Reset
- Alarm Cancel
- Trouble Indications
- Codes
- Duress Code
- Panic Switches
- Area Arming
- GOTO Area
- Testing Your System
- CONTROL
- Control Commands
- About UPB
- HAI Lighting Control (HLC) Format
- About CentraLite
- About Lutron RadioRA
- About ALC
- About X-10
- House Codes
- Unit Numbers
- Scrolling Through Names
- Controlling Units
- Timed Commands
- Status of a Unit
- Internal Flags
- Controlling Outputs
- All On / Off
- Leviton Scene Control
- Buttons
- Temperature Control
- HAI RC-Series Thermostats
- Programmable Energy Saver Modules (PESMs)
- Temperature Alarms
- Humidity
- Status
- Event Log
- Messages
- TELEPHONE CONTROL
- Telephone Interface
- In-House Phones
- Remote Phones
- Phone Access Denied - Remote Lockout
- Alternate Method
- Main Menu
- 1 - Control
- 2 - Security
- 3 - Button
- 4 - All
- 5 - Temperature
- 6 - Status
- 7 - Events
- 8 - Message
- 9 - Good-Bye
- Panic Button over the Phone (# # # # # #)
- Emergency Dial-Out
- Digital Dialer
- Voice Dialer
- PC Access
- Built-In Ethernet Port
- Controller IP Address, Port Number, and Encryption Key
- OmniPro II Ethernet Connections
- Connecting to Network via PC Access
- Dynamic DNS
- SETUP
- UNDERWRITER'S LABORATORIES REQUIREMENTS
- FEDERAL COMMUNICATION COMMISSION NOTICE:
- CANADIAN INDUSTRY CANADA NOTICE
- APPENDIX A - DIAL OUT PLANNER
- APPENDIX B - TEXT DESCRIPTION CHARACTER CODES
- APPENDIX C - VOICE DESCRIPTION CODES
CONTROL
Control Commands
The control features of the OmniPro II make it easy and convenient to control almost any light or appliance from the console or
over the telephone. You may also have your heating and air conditioning (HVAC) under control of the system, which will allow
you to save energy dollars by setting the temperature appropriately when you are home, asleep, or away.
Furthermore, the OmniPro II can be used to program lights to make the home or business look occupied as a deterrent to thieves.
The methods that the OmniPro II uses to control different devices are:
• UPB switches, modules, and keypads for lights and appliances
• CentraLite loads and relays on a LiteJet and Elegance lighting system
• RadioRA switches and dimmers on a Lutron RadioRA lighting system
• ALC switch modules for lights and appliances
• X-10 compatible modules (X-10, X-10 Pro, Leviton, PCS, ACT, Lightolier, etc.) for lights and small appliances.
• HAI Communicating Thermostats for controlling Heating, Ventilation, and Air Conditioning Systems.
• Programmable Energy Saver Modules (PESM) for central heating and air conditioning systems.
• Direct Output Control for relays to activate sprinklers, lighting, electric heating, etc.
An OmniPro II will control:
¾ 250 UPB switches, modules, and keypads (up to 31 rooms of HLC Lighting)
¾ 192 CentraLite loads and relays
¾ 64 RadioRA switches and dimmers
¾ 248 ALC switch modules
¾ 256 X-10 compatible modules (all sixteen house codes)
¾ 64 HAI Communicating Thermostats
¾ 8 PESMs or Voltage Outputs (expandable to 136)
OmniPro II also has 119 internal "flags" that are used for programming conditionals and executing programs.
About UPB
UPB is a powerline communications standard for lighting and home control. UPB is a robust, two-way digital powerline carrier
communications protocol which transmits signals over the existing wires in a home. UPB can coexist peacefully with X-10
systems, intercoms, baby monitors, speakers, etc. that communicate over the powerline.
Using a Powerline Interface Module (PIM), OmniPro II sends UPB commands over the existing electrical wiring to special
switches, modules, and keypad controllers (UPB devices) that are designed with UPB technology. UPB switches are two-way
devices, so OmniPro II knows the actual status of the switch when it is controlled locally. In addition, UPB switches, modules,
and keypads can be used to trigger macros in the OmniPro II controller.
Page 16