Instructions / Assembly

ASSEMBLY OF THE TREE
1. Locate the bottom section of the tree which is identified by
a label on the outer branches marked “A” (Fig 5).
2. Remove the protective plastic cap from the end of the pole,
(that is pinched to a point), and place that end into the tree
stand. Be sure that the pointed end of the pole extends to
the bottom of the stand.
3. Now tighten the eyebolts evenly on the tree stand; being
careful not to over-tighten (Fig 3).
ASSEMBLY INSTRUCTIONS
(We recommend wearing proper clothing in order to prevent
scratches that may occur during the assembly process.)
Carefully unpack the contents from the tree’s carton (Fig 1);
including the contents of the poly-bag that is adhered to the
interior flap of the tree’s carton.
Your tree should include the following components:
A folding metal tree stand with (3) eyebolts.
A 5 function push button foot pedal with cord and plug (Fig 6);
which is pre-attached at the lowest section of your tree (Fig 5).
The 7.5’ tree will have (3) tree sections; (“A”, “B” and “C”; as
shown in Fig 5).
ASSEMBLY OF THE TREE STAND
1. Remove the tree stand from the plastic bag, loosen the eye
bolt and open the tree stand to form an “X”.
2. Align the holes for the insertion of the remaining (2) eyebolts.
3. Insert each eyebolt and begin threading in a clockwise
direction for a couple of rotations only; leaving enough room
for the tree’s pole from section “A” to be inserted into the
assembled stand (Fig 2).
4. Place the tree stand in its desired location; as once the tree is
fully assembled, it may be too difficult to move and relocate.
Fig 2
CCT18
NOTE: ALTHOUGH THE LED LIGHT STRINGS ON THE TREE ARE
RATED FOR INDOOR OR OUTDOOR USE; THE COMBINATION OF THE
TREE WITH THE LED LIGHTS IS FOR INDOOR USE ONLY.
TROUBLESHOOTING
1. If failure to light, press the 5 function push button foot pedal; as it
may be in the “Off” mode.
2. If the top of the tree or another individual lettered section does not
illuminate, remove each section and then reinsert as instructed, to
ensure the electrical connection is made.
NOTE: The tree’s top is designed specifically for a secure and firm
connection point. Downward force will be needed to ensure that
the electrical connection occurs.
NOTE: A SPECIALTY NON-REPLACEABLE LED HAS BEEN
APPLIED TO YOUR PRE-LIT TREE; IN THE CASE THAT A
INDIVIDUAL LED BULB BURNS OUT, THE REMAINING LED BULBS
WILL CONTINUE TO STAY LIT.
1. Gently remove the plug from its electrical outlet, and carefully bind
the cord which contains the 5 function push button foot pedal and
plug.
2. Beginning with the tree’s top section; lift each section straight up
from the section below, and continue working downward.
NOTE: You may have to slightly wiggle each section as you lift each
section upward.
3. To remove the bottom and final section; loosen the eyebolts by
turning in a counter-clockwise direction and lift section “A” from the
support collar of the tree stand.
4. Gently fold the branches of each section upward, towards the
center, and position in the storage container.
NOTE: With the exception of the tree’s “top” section; by holding
each section upside down; the branches will collapse downward,
due to the hinging, aiding in the packing of each section into the
storage container.
5. Fully unthread the eyebolts from the tree’s stand and fold together;
placing in the storage container.
6. It is recommended to always store the tree in a cool, dry location
protected from excessive exposure to heat or sunlight.
NOTE: Store your remote control in a SAFE & DRY location and
remove the battery from remote control before storage.
DISASSEMBLY & STORAGE
Fig 3
4. Carefully cut the nylon strapping bounding the branches
upright.
CAUTION: Be extremely careful not to cut any of the exposed
light set wires.
5. Now gently guide the branches downward into place.
6. Beneath the canopy of section “A”, contain’s an 5 function push
button foot pedal with cord and plug (Fig 6).
Remove the twist-tie binding the cord together and insert the
plug into a working electrical outlet.
7. 5 function push button foot pedal operation:
Color Change, Steady Warm White, Twinkle Warm White, Steady
Multi, Twinkle Multi, and Off.
10. Once section “B” is fully inserted downward into section “A”;
both section “A” and section “B” will now be lit.
11. Again, carefully cut the nylon strapping bounding the
branches upright; being extremely careful not to cut any of
the exposed light set wires.
12. Now gently guide the branches of section “B” downward into
place.
13. Depending on the height of the tree you have purchased,
you will continue to build your tree upwards, section by
section, following the above steps until the tree is completely
assembled. Each section of the tree is labeled in alphabetical
order beginning from the bottom to the top.
8. Locate the next section of the tree which is identified by a
label on the outer branches marked “B” (Fig 5).
9. Remove the protective plastic cap from the end of the pole
on section “B”; insert that end onto the top of the pole of
section “A” (Fig 4).
Fig 4
EZ-POWER™ TECHNOLOGY
NOTE: Your tree has been designed with EZ-Power™
technology; allowing for each of the tree’s remaining sections
to light up automatically, upon a firm insertion of each
lettered section (Fig 5).
A
B
C
Foot
Pedal
Fig 5
Fig 1
FLOCKING OR GLITTER DISCLAIMER
Notice: Your pre-lit tree has been professionally flocked or
glittered.
Upon the tree sections being removed from its carton, you will notice
an accumulation of flocking or glitter at the base of the carton.
Do not be alarmed.
This loose flocking or glitter material was accounted for and
planned in the packing and manufacturing process of this tree.
In no way has the appearance or the integrity of the tree's
quality been compromised.
During future Holiday seasons you can expect a light dusting of
flocking or glitter to loosen from your tree during the packing and
unpacking process. Extra flocking or glitter has been adhered to
your tree to account for this minor annual loss.
The overall beauty of your tree will not be diminished.
Simply sweep or vacuum up the loose flocking or glitter upon the
assembly completion. During the flocking or glitter process the
light bulbs themselves have been flocked or glittered. This was
purposely done for the overall lighting effect of the tree.
PLEASE NOTE: Your flocked tree must NOT be stored in a plastic
bag or bags as moisture and condensation may occur, causing for
the discoloration of the flocking material.
Your flocked or glittered tree must be stored in a cool and dry location
protected from excessive exposure to moisture, heat or sunlight.
With proper care and proper storage location, you will experience
many years of enjoyment.
Fig 6
Model No. SL75256SF-GP62FTHO
Made in China
Printed in China
This is not a toy, for decorative use only.
DISTRIBUTED BY HOME DEPOT U.S.A., INC. 2455
PACES FERRY RD., N.W. Atlanta, GA 30339 All rights reserved.
This product was pre-tested before shipment and date
coded. In keeping with the National Electric Code, this
product is intended for seasonal (90 days max.) installation
and use. For problems or questions on this product call our
customer service toll-free at 1-877-527-0313.
18”
2018 Home Depot.com/US
7.5ft Starry Light Slim Frasier Fir Flocked Tree Instruction Sheet - 5 Function Foot Pedal (English)
Date: 3/22/18
Item # SL75256SF-GP62FTHO
15”