EnglishFrench Spanish OWNER’S MANUAL & OPERATING INSTRUCTIONS 1-800-874-6625 Homak Manufacturing 1605 Old Route 18 Suite 4-36, Wampum, PA 16157 Hours of operation: Monday - Friday 8:30 a.m. - 4:30 p.m Eastern Time Part No.
WARNING: 1. Read all safety instructions and safety tips before using this product, failure to do so may result in personal injury. 2. Ground all tools. If the tool is equipped with a three pin plug, it should be plugged into a three pin electrical socket. Never remove the ground pin. 3. Do not abuse the cord. Never use the cord to carry tools or pull the plug from an outlet. Keep cord away from heat, sharp edges, or moving parts. Replace damaged cords immediately.
Specifications: Tank size – 28” x 19” x 8” Assembled Dims – 38” x 21.5” x 37” Electrical Requirements – 120v, 60Hz Pump Capacity – 317 Gallons/Hr. Weight – 82lbs. Power Source Connection Power Requirements: This product is designed to operate on a properly grounded voltage, single-phase alternating current (ac) power source fused with a 20 amp time delayed fuse or circuit breaker.
Assembly Bottom Shelf 1. Locate the two Handles (04) and the Bottom Shelf (13) 2. Align the holes in the bottom of the Handles with the 4 holes in the corners of the Bottom Shelf. 3. Place Flat Washers (03) onto the Bolt (02) and insert Bolt through Handle and Bottom Shelf. 4. Place Flat Washer (03) and Lock Nut (07) onto end of Bolt and hand tighten 5. Repeat steps 3-4 for remaining holes in Bottom Shelf NOTE: DO NOT FULLY TIGHTEN NUTS AT THIS TIME Middle (Parts Drying) Shelf 1.
NOTE: DO NOT FULLY TIGHTEN NUTS AT THIS TIME Tank Note: You may need a second person to help properly align the Tank (08) to the Tank Mounts (06 and 25). 1. Place Flat Washer (03) onto Short Bolt (11) and insert through hole in Tank Mount. 2. Place Adjusting Washer (40) onto Short Bolt. 3. Slide the end of the Short Bolt (11) through the hole in the Mounting Bracket on Tank bottom 4. Place Flat Washer and Lock Nut (07) onto end of Short Bolt and hand tighten. 5.
ON positon. 4. Clean parts as needed. 5. Turn power switch to the OFF position. 6. Place parts on drying shelf until completely dry. 7. Empty drain tank, as needed, by sliding out of drying shelf brackets. WARNING: CLEAN OFF ANY ACCIDENTAL SPLASHES OF SOLVENT ON SKIN IMMEDIATELY, FOLLOWING THE SOLVENT MANUFACTUTER’S INSTRUCTIONS CAREFULLY. SEEK MEDICAL ATTENTION IF NECESSARY. When Not In Use: 1. Switch off pump, close the lid and disconnect from electrical supply 2.
1-800-874-6625 MANUEL DU PROPRIÉTAIRE MODE D’EMPLOI Homak Manufacturing 1605 Old Route 18 Suite 4-36, Wampum, PA 16157 Heures d’ouverture : Du lundi au vendredi 8h30 à 16h30 Heure de l’Est PORTABLE PARTS WASHER MODÈLE: RD00820290 ROUGE Piéce No.
MODE D’EMPLOI dépannage composer le q le service à la clientèle, WARNING: 1. Lire toutes les directives et consignes de sécurité avant d’utiliser ce produit afin d’éviter le risque de blessures. 2. Ground all tools. If the tool is equipped with a three pin plug, it should be plugged into a three pin electrical socket. Never remove the ground pin. 3. Do not abuse the cord. Never use the cord to carry tools or pull the plug from an outlet. Keep cord away from heat, sharp edges, or moving parts.
CARACTÉRISTIQUES TECHNIQUES: Tank size – 28” x 19” 8” Assembled Dims – 38” x 21.5” x 37” Electrical Requirements – 120v, 60Hz Pump Capacity – 317 Gallons/Hr. Weight – 82lbs. Power Source Connection Power Requirements: This product is designed to operate on a properly grounded voltage, single-phase alternating current (ac) power source fused with a 20 amp time delayed fuse or circuit breaker.
Assembly Bottom Shelf 1. Locate the two Handles (04) and the Bottom Shelf (13) 2. Align the holes in the bottom of the Handles with the 4 holes in the corners of the Bottom Shelf. 3. Place Flat Washers (03) onto the Bolt (02) and insert Bolt through Handle and Bottom Shelf. 4. Place Flat Washer (03) and Lock Nut (07) onto end of Bolt and hand tighten 5. Repeat steps 3-4 for remaining holes in Bottom Shelf NOTE: DO NOT FULLY TIGHTEN NUTS AT THIS TIME Middle (Parts Drying) Shelf 1.
NOTE: DO NOT FULLY TIGHTEN NUTS AT THIS TIME Tank Note: You may need a second person to help properly align the Tank (08) to the Tank Mounts (06 and 25). 1. Place Flat Washer (03) onto Short Bolt (11) and insert through hole in Tank Mount. 2. Place Adjusting Washer (40) onto Short Bolt. 3. Slide the end of the Short Bolt (11) through the hole in the Mounting Bracket on Tank bottom 4. Place Flat Washer and Lock Nut (07) onto end of Short Bolt and hand tighten. 5.
ON positon. 4. Clean parts as needed. 5. Turn power switch to the OFF position. 6. Place parts on drying shelf until completely dry. 7. Empty drain tank, as needed, by sliding out of drying shelf brackets. WARNING: CLEAN OFF ANY ACCIDENTAL SPLASHES OF SOLVENT ON SKIN IMMEDIATELY, FOLLOWING THE SOLVENT MANUFACTUTER’S INSTRUCTIONS CAREFULLY. SEEK MEDICAL ATTENTION IF NECESSARY. When Not In Use: 1. Switch off pump, close the lid and disconnect from electrical supply 2.
EnglishFrench Spanish OWNER’S MANUAL & OPERATING INSTRUCTIONS 1-800-874-6625 Homak Manufacturing 1605 Old Route 18 Suite 4-36, Wampum, PA 16157 Hours of operation: Monday - Friday 8:30 a.m. - 4:30 p.m Eastern Time PORTABLE PARTS WASHER MODEL: RD00820290 RED Pieza No. Descripción Qty.
WARNING: 1. Read all safety instructions and safety tips before using this product, failure to do so may result in personal injury. 2. Ground all tools. If the tool is equipped with a three pin plug, it should be plugged into a three pin electrical socket. Never remove the ground pin. 3. Do not abuse the cord. Never use the cord to carry tools or pull the plug from an outlet. Keep cord away from heat, sharp edges, or moving parts. Replace damaged cords immediately.
Specifications: Tank size – 28” x 19” x 8” Assembled Dims – 38” x 21.5” x 37” Electrical Requirements – 120v, 60Hz Pump Capacity – 317 Gallons/Hr. Weight – 82lbs. Power Source Connection Power Requirements: This product is designed to operate on a properly grounded voltage, single-phase alternating current (ac) power source fused with a 20 amp time delayed fuse or circuit breaker.
Assembly Bottom Shelf 1. Locate the two Handles (04) and the Bottom Shelf (13) 2. Align the holes in the bottom of the Handles with the 4 holes in the corners of the Bottom Shelf. 3. Place Flat Washers (03) onto the Bolt (02) and insert Bolt through Handle and Bottom Shelf. 4. Place Flat Washer (03) and Lock Nut (07) onto end of Bolt and hand tighten 5. Repeat steps 3-4 for remaining holes in Bottom Shelf NOTE: DO NOT FULLY TIGHTEN NUTS AT THIS TIME Middle (Parts Drying) Shelf 1.
NOTE: DO NOT FULLY TIGHTEN NUTS AT THIS TIME Tank Note: You may need a second person to help properly align the Tank (08) to the Tank Mounts (06 and 25). 1. Place Flat Washer (03) onto Short Bolt (11) and insert through hole in Tank Mount. 2. Place Adjusting Washer (40) onto Short Bolt. 3. Slide the end of the Short Bolt (11) through the hole in the Mounting Bracket on Tank bottom 4. Place Flat Washer and Lock Nut (07) onto end of Short Bolt and hand tighten. 5.
ON positon. 4. Clean parts as needed. 5. Turn power switch to the OFF position. 6. Place parts on drying shelf until completely dry. 7. Empty drain tank, as needed, by sliding out of drying shelf brackets. WARNING: CLEAN OFF ANY ACCIDENTAL SPLASHES OF SOLVENT ON SKIN IMMEDIATELY, FOLLOWING THE SOLVENT MANUFACTUTER’S INSTRUCTIONS CAREFULLY. SEEK MEDICAL ATTENTION IF NECESSARY. When Not In Use: 1. Switch off pump, close the lid and disconnect from electrical supply 2.
- 19 -
PRODUCT REGISTRATION Thank you for purchasing this quality HOMAK product. Please take the time to register your manufacturer’s code and product by calling 1-800-874-6625 or by visiting www.homak.com and clicking the “Product Registration” link.
