Datasheet

Hold the capacitors to keep the axis
vertical, bend it 90 degrees as shown below and
bend back to the original position. This operation
shall be done for 2~3s. and repeated for the
following times.
Bending force: 5N(weight :0.51kg)
Test time : 2 times
No mechanical damage such as lead
breakage or loosening.
C≤100pF 1MHz 10% 1.0 0.2Vrms
C>100pF 1KHz 10%
Item Specification Test Condition
Operation
Temperature
Visual No abnormal exterior appearance Visual Inspection
Capacitance
Within The Specified Tolerance
Insulation
Resistance
10,000M or 500/C whichever is smaller
for rated voltage>10V and greater 100/C for
rated voltage≤10V
Applied Voltage: Rated Voltage Charge
Time : 60 5 sec. Charge-Discharge
current shall be less than 50mA current..
Withstanding
Voltage
No dielectric breakdown or mechanical
breakdown
Class Frequency Voltage
Perform a heat treatment at 150 5 for 30min.
then place room temp. for 24 2hr.
X7R/X5R/Y5V
C 10uF 1KHz 10% 1.0 0.2Vrms
C 10uF 120Hz 20% 0.5 0.2Vrms
Class (X7R,X5R,Y5V):
Please see HEC specification data sheet for
details
V 50 : 250% Rated Voltage
V 500V : 200% Rated Voltage
500V V 1000V: 150% Rated Voltage
1000 V :120% Rated Voltage
for 1~5 sec. Current is limited to less than 50mA.
Dissipation
Factor
Class (NPO):
More Than 30pF : Q 1000
30pF & Below: Q 400 20C (C:Cap., pF)
Quality Factor
NPO
RDC Series Specification & Test Condition
Lead Strength
Tensile
Strength
Solderability
Completely immerse both terminations in solder
at 235 5 for 2 0.5s
Solder : H63A
Flux :Rosin
Dipping :By 1.5~2.0mm form the root of lead
Leads shall be covered by new solder more
than 75% of its surface
Temperature
Capacitance
Coefficient
(C2-C1)/C1 × 100%
T1:Standard Temperature(25 )
T2:Test Temperature
C1:Capacitance at Standard Temperature
C2:Capacitance a Test Temperature
Class :
[C2-C1/C1(T2-T1)] × 100%
Class :
Bending
Strength .
No mechanical damage such as lead
breakage and loosing.
Pulling strength: 5N
Holding time: 10 1s
No mechanical damage such as lead
breakage and loosing.
Char. Temp. Range Cap. Change
NPO (N) -55 ~ +125 30ppm/
X7R (X) -55 ~ +125 15%
X5R (B) -55 ~+85 15%
Y5V (Y) -30 ~+85 +22% ~-82%
Appearance
No mechanical damage shall occur
Resistance to
Soldering Heat
Capacitance
Q / Tanδ To satisfy the specified initial value
Insulation
Resistance
Completely soak both terminations in solder at
250 5 for 5 1s
Solder : H63A
Flux :Rosin
Dipping :By 1.5~2.0mm from the root of lead
Class
X7R,X5R : ≤ 10% of initial value
Y5V : ≤ 20% of initial value
Class (NPO):
Within 2.5% or 0.25pF whichever
is larger of initial value
To satisfy the specified initial value
RDC Series-Radial Dipped Ceramic Capacitor
Holy Stone
Please see HEC specification data sheet for
details
- 101 -