GPSmile 61CS Portable Automobile Navigation System Product User Manual Registered information HOLUX and GPSmile are trademarks of HOLUX Technology, Inc. All other trademarks belong to registered companies. The contents of this manual will be modified without further notice. The operation temperature for the product is between -10℃~60℃. Operating or recharging in an environment with a temperature over 50℃ might cause the system to malfunction.
Safety Precautions • Select the install location must be cautiously. HOLUX will not bear any responsibility if the user does not follow the correct device installing procedure. • About the power adapter: 1. Do not use the power adapter in a wet environment. When hands and feet are wet, do not touch the power adapter. 2. While using the power adaptor, ensure that the area is well ventilated. Do not let paper or other material cover the power adaptor, as this will interfere with cooling.
Content Preface ...................................................................... 1 Copyright ............................................................... 1 Precautions and Notices ............................................ 2 Package Contents ...................................................... 3 Device and Main Accessory .................................... 3 Motorbike RAM Mount Accessory (Optional) .......... 4 Optional accessory .............................................
Time/ Language ............................................... 28 Time Format .................................................. 29 Time Zone ..................................................... 30 Language ...................................................... 31 Bluetooth.......................................................... 32 System setup .................................................... 36 GPS ............................................................... 37 Factory Reset .....................
Preface We appreciate your purchase of the HOLUX motorbike navigation. Please read all instructions thoroughly for a full understanding of the products’ features. Copyright Without the written consent of HOLUX Technology, Inc, this manual, including the product and the software, may not be duplicated, transmitted, recorded or saved on storage devices. Furthermore, it shall not be translated under any circumstances into any other languages. Copyright ©2012 HOLUX Technology, Inc. All rights reserved.
Precautions and Notices Please thoroughly read this manual of operating instructions and explanations. Only use original factory approved batteries and accessories to prevent unexpected damage. If the correct procedures were not followed for operation or incompatible accessories were connected, this is a violation of the warrantee agreement and will automatically void the warrantee. This may also cause personal safety issues. • For your own safety, do not operate the controls of the product while driving.
Package Contents Device and Main Accessory Your product should include the following accessories: GPSmile 61CS Cradle DC-DC Adapter Car Charger Screw kit (main accessory) 3
Motorbike RAM Mount Accessory (Optional) 2 1 3 4 5 6 7 1. U-bolt Rail Mount 2. Device Base Plate 3. Motorcycle Handlebar Base 4. Double Socket Arm 5. Plastic Cushion 6. Square Rubber Neck 7.
Basic Operation Introduction Front View Main menu button 4.
Accessories Cradle Screw I/O cap I/O interface 6
Getting Started Install Cradle 1. Loosen the screw of cradle top. screw 2. Open the cap of cradle top. 3. Open the I/O cap.
4. Insert the device concave into the cradle tabs. ※ Please make sure the I/O pin is not wet or dirty. Concave Tab 5. Slide the GPS into the cradle fitting holes to secure. 6. Make sure the device is tightly fixed with the bracket, and gently close the cradle cap. 7. Tighten the screw.
Remove Cradle 1. Loosen the screw of cradle top. 2. Open the cradle cap and remove the device. 3.
Install motorcycle RAM mount (Optional) 「A」Device Base Plate 「B」Double Socket Arm 「C」Motorcycle Handlebar Base A B C Thread the bolts and nuts (screw kit of main accessory) to attach the「A」to cradle. A Tighten the nuts to secure the「A」.
There are two solutions to install Motorcycle RAM mount: 「motorcycle handlebar」or 「brake/ clutch」. Method 1: To install at handlebar with Ubolt (1) 「U-bolt」slip into 「Square rubber Neck」to protect the handlebar from scratching.
(2) Place the U-bolt around the handlebar, and thread the ends through the 「C」. C (3) To avoid slip, place 「plastic cushion」 between「U-bolt」 and handlebar. (4) Tighten the nuts to secure the base. Do not over tighten.
Method 2: To install at clutch/brake clamp bracket (1) Remove the two factory bolts on your clutch/brake clamp bracket. (2) Thread the new bolts (Screw kit of RAM mount) through the washers,「C」, spacers, and clamp bracket. (3) Tighten the bolts to secure the base. ※ There are long (QTY.2) and short (QTY.2) bolts in RAM mount screw kit, please select that you need to install. After install the「C」at proper location, install other components.
Attach the ball of the 「C」with one side of 「B」. B C Align the ball of the 「A」with the other side of「B」. A Tighten the knob slightly.
(1) Adjust「A」and 「C」for better viewing and operation. (2) Tighten the knob of 「B」to secure the mount. A B C For your riding safety, please loosen the knob of「B」to adjust the screen for better viewing and operation. After confirm the viewing, tighten the knob of「B」to secure the mount. Remind you: do not operate the device when you ride. ※ Note: Damage due to modifications, improper installation, road hazards or accident, are not covered.
Install/ Remove Battery Please make sure the battery is installed before using the device. 1. Open the battery lid. 2. Install or Remove the battery. Printing side facing up 3. Restore the battery lid.
Charging Battery Connect the car charger or AC adapter to charging. The charging temperature for the product is between 0℃~45℃. 1. Open the battery lid. AC adapter 2. Connect the USB adapter to a wall outlet. USB ※ AC adapter (5V/2A) is an optional accessory.
Install SD Card (Optional) 1. Open the battery lid and remove the battery. 2. Open SD card slot. 3. Insert SD card with its chip facing down and flat into the SD card slot.
4. Push upward to lock the SD card slot. 5. Put into the battery. 6. Restore the battery lid.
Device connection Diagram Car Charger GPSmile 61CS DC-DC Adapter (12V 5V) ※ Note: Please connect DC-DC adapter to 「ACC ignition switching circuit」. Do not connect to positive/ negative electrode of battery directly to avoid exhaustion of battery power. ※ If you are unsure about attaching the mount kit or adapter yourself, ask a professional to fit it for you. ※ The user shall determine the suitability of the product for its intended use and connect.
Operating Methods Startup/ Shutdown Please press and hold the power button for several seconds to turn on/ off the device. ON/OFF Power button When the device is turned on, the screen will show the main screen consisting of three functions: Shortcut1, Shortcut2 and settings. Directly select an icon on the screen to use the function.
Hot key Press the [Hot key] to enter the [Brightness/ Volume] setup menu. Click button on the bottom-left corner screen to access Bluetooth setup menu. Hot key For details, please refer to the [Brightness/Volume] and [Bluetooth] sections.
Battery Status The icon displays the remaining battery power. The icon means the battery power is lower than 15%, please charge the battery immediately.
Function Menu During the first startup, the screen will show the main screen consisting of three functions: Shortcut1, Shortcut2 and settings. Directly select an icon on the screen to use the function. Shortcut1/ Shortcut2 Drivers can set shortcuts on the main menu to a program that compatible with GPSmile 61CS. ※ For first setting, you can click the icon directly to enter 「Setting」「Shortcut」menu to setting. ※ Notes: ．GPSmile 61CS is only compatible with WinCE 6.0 programs.
Settings After starting up the system, select the [Settings] button to enter. The settings menu appears as shown above. The following sections describe these buttons and functions. You can customize the device settings such as brightness/ volume, Time/Language, Bluetooth, and System.
Brightness/ Volume Click [Brightness/volume] button to access Brightness/volume setup menu. Select button to increase/decrease brightness. There are ten levels. Select levels. Click button to adjust volume. There are ten button to go back to the previous page.
※Tip: Press the [Hot key] on the top of the device to quickly access [Brightness/ Volume] setup menu.
Time/ Language Click [Time/Language] button to access Time/ Language setup menu.
Time Format Select [Time Format] setup menu. to enter time format Select preferred time format from the menu. Click button to go back to the previous page.
Time Zone Select [Time Zone] setup menu. Select Click to enter time zone button to choose the correct time zone. button to go back to the previous page.
Language Select [Language] menu. to enter language setup Select preferred language from the menu. Click button to go back to the previous page.
Bluetooth Click menu. Click [Bluetooth] button to access Bluetooth setup button to search bluetooth devices.
The graphic shown below indicating the Bluetooth is searching new devices. During the Bluetooth searching process, users can cancel the process by click Press the press the button. button and a message appears on the screen; button to exit the search, or press the button to continue searching.
After completed the scanning process, GPSmile 61CS will display a list of scanned devices. Select the particular Bluetooth device from the list, and click the "Connect” button to enable the function.
When no devices were found during the scanning process, the following message will be shown on screen. Click button to go back and retry the Bluetooth scanning process again.
System setup Click [System] button to access system setup menu. In system setup menu, the items contain [GPS]、[Factory Reset]、[Shortcut]、[Mass Storage Mode]、[Version Information] and [Calibrate Screen]. The followings describe these buttons and functions.
GPS Select [GPS] button to enter satellite status page. Positioning precision Satellite signal strength Satellite number Positioning status GPS measured Height GPS Estimated Position Error ※ When searching satellite signal, GPSmile 61CS will display 「Acquiring」. When「3D fixed」is displayed, 61CS has fully acquired the GPS signal and is ready for use.
Reset GPS Click button to reset GPS. Click button to go back to the previous page.
Factory Reset Select [Factory Reset] to restore the factory default settings. Click button to restore to factory defaults. Click button to go back to the previous page. ※ Note: once the device is reset to factory defaults, all settings you set will be erased.
Shortcut Select [Shortcut] to access shortcut setup menu. To set shortcuts on main menu to a program, please see the example below on how to select the shortcuts.
To set the shortcut1: Step1. Click [Shortcut1] icon to enter shortcut1 setup menu. On the shortcut1 page, set [Application Path], [Name] and [Icon]. Step2. Click [Application Path] to enter folder list page. Select button to choose the correct folder icon. Click the .exe file in folders directly to specify the program as the shortcut. Click button to go back to the previous page.
※ Note: If you store the application program in “Resident Flash” and “SD card”; click [Application Page] icon, the page will display “Resident Flash” and “SDMMC (SD card)” two folders. ※ How to place files in SD card: (1) Create a folder in SD card. (2) Store the program in the folder. (3) Click the .exe file of the program on storage location.
Step3. Click [Name] to enter input title menu. Use digital keypad on the screen to input the title name. You can input English (uppercase/ lowercase), number and symbol. After input value, click to save the value and return. button to go Click back to the previous page.
Step4. Click [Icon] to enter the icon list menu. Select button to switch the icon list page, and click the icon to setup directly. Click button to go back to the previous page. Step5. After input [Application Path], [Name] and [Icon], click the setting. to save The shortcut that you set will be displayed on the main menu.
Mass Storage Mode Select enter [Mass Storage Mode] and connect device to a computer, SD card files are now accessible from the connected PC. The page below indicates the device not yet connected to a PC.
The page below indicated the device is now connected to a PC.
Version Information The screen displays the OS and AP version information.
Calibrate Screen Select [Calibrate Screen] to start the screen calibration procedure. Use the finger/stylus and touch the cross at the center of the screen. Continue the calibration by touching the cross. The system setting page will return when adjustment is finished.
Warranty Statement • This warranty applies to parts and services that are manufactured and sold through Holux Technology Inc. The local area covered is Taiwan; the warranty length is one year from date of purchase (starting from the date on the sales receipt). Under normal user operation, Holux Technology provides free repair services. After repair, the replaced parts are the properties of Holux Technology Inc.
Technical Support • If there are any questions regarding the use of this product, please log on to the website www.holux.com and see the FAQ. Maintenance Service HOLUX Technology, Inc. +886-3-6687000 website: www.holux.com FAQ: FAQ.holux.com or Contact your nearest dealer, for further support. HOLUX Technology, Inc. www.holux.
Federal Regulations This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
grantee of this device could void the user's authority to operate this equipment. RF Exposure Warning This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operated in conjunction with any other antenna or transmitter.
