GPSmile 61CS Navigation System Product User Manual Registered info HOLUX and GPSmile are trademarks of HOLUX Technology, Inc. All other trademarks belong to registered companies. Note The contents of this manual will be modified without further notice. The operation temperature for the product is between -10℃~50℃. Operating or recharging in an environment with a temperature over 50℃ might cause the system to malfunction. However, this should be considered a normal phenomenon.
Safety Precautions The device should only be used with the supplied batteries. About the battery 1. A Lithium battery is built into the device. To prevent fire or skin burns, do not disassemble, pierce, impact, or expose the battery to fire. The battery will crack, explode, or release dangerous chemicals if placed in a fire. Important instructions 1. Note: Replacing with an incorrect battery may result in an explosion. When disposing of the battery, follow the instructions.
Warranty Statement This warranty applies to parts and services that are manufactured and sold through Holux Technology Inc. The local area covered is Taiwan; the warranty length is one year from date of purchase (starting from the date on the sales receipt). Under normal user operation, Holux Technology provides free repair services. After repair, the replaced parts are the properties of Holux Technology Inc.
Technical Support If there are any questions regarding the use of this product, please log on to the website www.holux.com and see the FAQ. Maintenance Service HOLUX Technology, Inc. +886-3-6687000 Web Site: www.holux.com or Contact your nearest dealer, for further support. HOLUX Technology, Inc. www.holux.
Table of Contents Safety Precautions ............................................................................. ii Warranty Statement .......................................................................... iii Technical Support ............................................................................. iv Maintenance Service......................................................................... iv Preface .............................................................................................
Remove Cradle ............................................................................ 13 Install motorcycle RAM mount ................................................... 14 Install/ Remove Battery..................................................................... 19 Device connection Diagram ........................................................
Preface We appreciate your purchase of the HOLUX car navigation. Please read all instructions thoroughly for a full understanding of the products’ features. Precautions and Notices For your own safety, do not operate the controls of the product while driving. Use this product prudently. The product is intended to be used only as a navigation aid. It is not for precise measurement of direction, distance, location or topography. The calculated route is for reference only.
Copyright Without the written consent of HOLUX Technology, Inc, this manual, including the product and the software, may not be duplicated, transmitted, recorded or saved on storage devices. Furthermore, it shall not be translated under any circumstances into any other languages. Copyright ©2012 HOLUX Technology, Inc. All rights reserved. Important Notice Please thoroughly read this manual of operating instructions and explanations.
Product Specification Item Description Dimension Typ. 130(L)x 92.2(W)x29(H) mm Weight Typ. 280 g (including battery) Processor Memory SiRF Atlas IV 500MHz, ARM11. FLASH: 4GB NAND Flash Memory(MLC) RAM: 128MB DDR1(32bit) 32KB EEPROM Audio 2S CODEC Built-in Speaker (8 Ohm/2W) Display 480 RGB (W) x 272(H) dots, 4.3” Blanview LCD 0.198 mm dot pitch RGB vertical stripe LCM colors: 65536 colors(16 bits) Brightness, Typ.
I/O Interface Support 12pin I/O board for motorcycle cradle Card Slot Micro SD Slot x 1, Micro SD™, Support 8GB(Max.), SD standard host spec (2.0) compatible Battery Rechargeable Li-Ion battery 1050mAh Normal voltage: 3.7V Charger voltage: 4.2V Suspend current typical 6mA Power management Power Requirement 5.2V(+-)0.25V NFORE, NF 2303 Bluetooth firmware version: H10620-V118R8(no noise gate) Class 2: 0.25mW ~ 2.
B. Software Spec. Support upgrade OS&AP via Micro SD Card B. Tools 1 Support Active Sync or Mass Storage via mini USB interface HSP (Headset Profile) Bluetooth Provide nFore Middleware for development B. Profile A2DP(Advanced Audio Distribution Profile) 2 support Provide nFore Middleware for development Class 2 C. Standard Accessories C. 1 C. 2 C.3 C.4 C.5 C.6 Car charger Motorbike Charger Cradle with power USB Cable Cable quick guide Tool DVD Gift box UART Cable Input : 10.
E. Certification E. 1 CE/FCC FCC ID: RJI-NAV61CS PND Product Performance Long-term F.19 Receive Long-term Cold F. 20 Start Test Place: HOLUX Test Environment: Open sky at HOLUX building Criteria: Average C/N≧40 dB, 3 highest sattelites Position drift range≦15 m Test Place: HOLUX Test Environment: Open sky at HOLUX building Criteria: TTFF ≦ 43s PND Battery Life F.
First time use Package Contents Your product should include the following accessories: GPSmile 61CS Cradle DC-DC Adapter Car Charger Screw kit (main accessory) 7
Motorbike RAM Mount Accessory 2 1 3 4 5 6 7 1. U-bolt Rail Mount 2. Device Base Plate 3. Motorcycle Handlebar Base 4. Double Socket Arm 5. Plastic Cushion 6. Square Rubber Neck 7.
Basic Operation Introduction Front View Main menu button 4.
Accessories Cradle Screw I/O cap I/O interface 10
Getting Started Install Cradle 1. Loosen the screw of cradle top. screw 2. Open the cap of cradle top. 3. Open the I/O cap. 4. Insert the device concave into the cradle tabs. ※ Please make sure the I/O pin is not wet or dirty.
Tab 5. Slide the GPS into the cradle fitting holes to secure. 6. Make sure the device is tightly fixed with the bracket, and gently close the cradle cap. 7. Tighten the screw.
Remove Cradle 1. Loosen the screw of cradle top. 2. Open the cradle cap and remove the device. 3.
Install motorcycle RAM mount 「A」Device Base Plate 「B」Double Socket Arm 「C」Motorcycle Handlebar Base A B C Thread the bolts and nuts (screw kit of main accessory) to attach the 「A」to cradle. A Tighten the nuts to secure the「A」.
There are two solutions to install Motorcycle RAM mount: 「motorcycle handlebar」or 「brake/ clutch」. Method 1: To install at handlebar with U-bolt (1) 「U-bolt」slip into 「Square rubber Neck」to protect the handlebar from scratching.
(2) Place the U-bolt around the handlebar, and thread the ends through the 「C」. C (3) To avoid slip, place 「plastic cushion」 between「U-bolt」and handlebar. (4) Tighten the nuts to secure the base. Do not over tighten. Method 2: To install at clutch/brake clamp bracket (1) Remove the two factory bolts on your clutch/brake clamp bracket. (2) Thread the new bolts (Screw kit of RAM mount) through the washers,「C」, spacers, and clamp bracket. (3) Tighten the bolts to secure the base. ※ There are long (QTY.
and short (QTY.2) bolts in RAM mount screw kit, please select that you need to install. After install the「C」at proper location, install other components. Attach the ball of the 「C」with one side of 「B」. B C Align the ball of the 「A」 with the other side of 「B」. A Tighten the knob slightly.
(1) Adjust「A」and「C」 for better viewing and operation. (2) Tighten the knob of 「B」to secure the mount. A B C For your riding safety, please loosen the knob of 「B」to adjust the screen for better viewing and operation. After confirm the viewing, tighten the knob of「B」to secure the mount. Remind you: do not operate the device when you ride. ※ Note: Damage due to modifications, improper installation, road hazards or accident, are not covered.
Install/ Remove Battery Please make sure the battery is installed before using the device. 1. Open the battery lid 2. Install or Remove the battery Printing side facing up Pull the plastic to remove the battery 3. Restore the battery lid.
Device connection Diagram Car Charger GPSmile 61CS DC-DC Adapter (12V5V) 20
FCC Notices This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. CAUTION: Change or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.