73.5" POST KIT KIT DE POSTES 73.
HOFT TIPS! HOFT CONSEJOS! When purchasing your planks, be sure to choose wisely, without defects. Comprar planchas sin defectos. To ensure your planks are leveled, use a level on your first plank and adjust railblocks accordingly. Para garantizar que las planchas estén rectas, utilizar un nivel en la primera plancha y ajustar los topes en consecuencia. Push down on each plank while assembling so that spacer teeth do their work.
Parts Partes KIT A6 KIT B6 KIT C6 1X END POST 1X POSTE DE FINAL 1X CORNER POST 1X POSTE DE ESQUINA 1X LINE POST 1X POSTE LINEAL ALLEN KEY LLAVE ALLEN POST SCREW TORNILLO PARA POSTE SPACER SEPARADOR RAIL BLOCK TOPE DE RIEL 2X 2X 2X 4X 4X 4X 11X 22X 22X 1X 2X 2X A6 B6 C6 A6 B6 C6 A6 B6 C6 A6 B6 C6 + ANCHOR PLATE PLACA DE FIJACIÓN CAP TAPÓN 1X 1X 1X 1X 1X 1X A6 B6 C6 A6 B6 C6 SECTION BRACKET & SCEWS SOPORTE DE SECCIÓN & TORNILLO 1X 2X 2X A6 B6 C6 RAIL BLOCK & CAP SCREW
Installation *IMPORTANT : Make sure to read the whole installation guide before starting your project. *IMPORTANTE : Leer atentamente esta guía de instalación antes de empezar con el proyecto. 1 Install post screws with Allen key to fasten post and anchor plate together. Colocar los tornillos para postes con la llave allen para fijar el poste a la placa de fijación.
WOOD/COMPOSITE Drill pilot holes before screwing 3/8’’ D x 3’’ L minimum lag bolts (not included). MADERA/COMPOSITE Marcar 4 orificios pequeños antes de atornillar los 4 tirafondos de 3/8’’ x 3’’ mínimo (no incluidos). CONCRETE FOUNDATIONS Install 3/8’’ D x 3’’ L minimum concrete anchors (not included). CEMENTO Instalar 4 anclajes para cemento de 3/8’’ x 3’’ mínimo (no incluidos). * Make sure posts are properly aligned and leveled before anchoring.
Wood planks / Planchas de madera 72’’ MAXIMUM* Composite 60’’ MAXIMUM* Posts / Postes 70’’3/4 MAXIMUM* 3 *IMPORTANT : Anchor posts 1’’1/4 closer than the length of your chosen boards, so that boards insert into the rail. *IMPORTANTE : Anclar los postes a una distancia de 1’’1/4 menos que el largo de las planchas que se desean insertar en el riel.
4 Determine the height of your first board by sliding a railblock in each rail and screw at the desired height. Para determinar la altura de la primera plancha, deslizar un tope de riel en cada riel y atornillar a la altura deseada. *IMPORTANT : Use railblock screw and screw until flush with the railblock. *IMPORTANT : Utilizar un tornillo para tope de riel. Atornillar hasta que el perno quede completamente alineado con el tope de riel.
5 Between each wood boards, insert a spacer in post rail and press down on each board. Entre cada plancha, introducir un separador en cada riel.
6 Slide section bracket on top of last board and insert the wood screw to solidify assembly. This part will slide down with top board as wood settles. Deslizar el soporte de sección por la parte superior de la última plancha y atornillar ambos tornillos para asegurar el conjunto.
7 Secure cap to top of post with the cap screw and allen key screw until flush with the cap. Fijar el tapón a la parte superior del poste con el tornillo correspondientey la llave allen. Atornillar hasta que quede bien alineado on el tapón.
WARNINGS! ¡ATENCIÓN! Always follow applicable building codes before using this product and consider whether you are required to add a railing or guard to your application. Before using this product, ensure wood, composite or cement flooring/decking is suitable to anchor lag bolts. Deck boards must be at least 1 ½’’ thick, in good condition and free from rot and damage. NEVER use this product as a railing or guard, to do so could result in injury or damage. Should not be used above 60cm / 23.
www.hoftsolutions.com info@hoftsolutions.
