User Manual

ManualsBrandsHOBO by Onset ManualsCurrent SensorsHOBO by Onset UX90-006 Occupancy/Light Logger

HOBO® Occupancy/Light

Data Logger (UX90-005x/-006x) Manual

15433-H

The HOBO Occupancy/Light data logger monitors room occupancy up to 5 or 12 meters away

(depending on the model) as well as indoor light changes with its integrated sensors. Using

HOBOware®, you can easily configure both channels to record occupancy and light on and off

conditions for building energy audits. This compact data logger has a built-in LCD screen for

checking status, remaining battery level, and memory consumption. You can also use the LCD

screen to quickly calibrate the logger to the light level in the room or select preset sensitivity

thresholds with HOBOware. There are two models of both types of loggers: the UX90-005/-006

has a memory capacity of 128 KB while the UX90-005M/-006M has 512 KB.

Specifications

Occupancy Sensor

Detection Range UX90-005x: maximum 5 m (16.4 ft)

UX90-006x: maximum 12 m (39.4 ft)

Detection Performance UX90-005x: 94° (±47°) Horizontal; 82° (±41°) Vertical (see Figure A)

UX90-006x: 102° (±51°) Horizontal; 92° (±46°) Vertical (see Figure B)

Detection Zones UX90-005x: 64 (see Figure A)

UX90-006x: 92 (see Figure B)

Light Sensor

Light Threshold > 65 lux

Light Type LED, CFL, fluorescent, HID, incandescent, natural

Logger

Memory Modes Wrap when full or stop when full

Start Modes Immediate, push button, date & time, or next interval

Stop Modes When memory full, push button, or date & time

Time Accuracy ±1 minute per month at 25°C (77°F) (see Plot A)

Power Source One 3V CR2032 lithium battery and USB cable

Battery Life 1 year typical use

Memory UX90-005/-006: 128 KB (84,650 measurements, maximum)

UX90-005M/-006M: 512 KB (346,795 measurements, maximum)

Download Type USB 2.0 interface

Full Memory Download Time 10 seconds for 128 KB, 30 seconds for 512 KB

Operating Range Logging: -20° to 70°C (-4° to 158°F); 0 to 95% RH (non-condensing)

Launch/Readout: 0° to 50°C (32° to 122°F) per USB specification

Occupancy Sensor Range: 20° to 60°C (-4° to 140°F); 15 to 85% RH

(non-condensing)

LCD LCD is visible from: 0° to 50°C (32° to 122°F); the LCD may react slowly

or go blank in temperatures outside this range

Size UX90-005x: 3.66 x 8.48 x 2.36 cm (1.44 x 3.34 x 0.93 in.)

UX90-006x: 3.66 x 8.48 x 2.87 cm (1.44 x 3.34 x 1.13 in.)

Weight 30 g (1.06 oz)

Environmental Rating IP50

The CE Marking identifies this product as complying with all relevant

directives in the European Union (EU).

HOBO Occupancy/Light

Data Logger

Models: UX90-005

UX90-005M

UX90-006

UX90-006M

Included Items:

• Command™ strip

• Double-sided tape

• Hook & loop strap

Required Items:

• HOBOware 3.3 or later

• USB cable (included with

software)

Accessories:

• Light pipe (UX90-LIGHT-

PIPE-1)

• U-Shuttle (U-DT-1)

UX90

005x

UX90

006x

Summary of content (7 pages)

PAGE 1
HOBO® Occupancy/Light Data Logger (UX90-005x/-006x) Manual UX90-005x The HOBO Occupancy/Light data logger monitors room occupancy up to 5 or 12 meters away (depending on the model) as well as indoor light changes with its integrated sensors. Using HOBOware®, you can easily configure both channels to record occupancy and light on and off conditions for building energy audits. This compact data logger has a built-in LCD screen for checking status, remaining battery level, and memory consumption.
PAGE 2
HOBO Occupancy/Light Data Logger (UX90-005x/-006x) Manual Specifications (continued) Plot A: Time Accuracy Horizontal Horizontal X-Y Cross Section X-Y Cross Section Vertical Vertical Figure A: UX90-005 Detection Area Figure B: UX90-006 Detection Area Logger Components and Operation Battery Tray Start/Stop Button Calibration Button Light Sensor an internal event (see Recording Internal Logger Events) or to turn the LCD screen on if the option to turn off the LCD has been enabled (see Setting up th
PAGE 3
HOBO Occupancy/Light Data Logger (UX90-005x/-006x) Manual Mounting Loops: Use the two mounting loops to mount the logger with the hook-and-loop strapping (see Mounting the Logger). LCD Symbol Description Time display when logger is logging: This shows the total amount of time the room has been occupied or the light has been on since logging began, ranging from seconds to days. This example indicates the room has been occupied or the light has been on for a total of 5 minutes and 38 seconds.
PAGE 4
HOBO Occupancy/Light Data Logger (UX90-005x/-006x) Manual sensor configuration. Any filtered series will be automatically available upon reading out the logger. 6. Set the units to display on the LCD screen. Select either Time or %. 7. If the logger is configured to record runtime, choose a logging interval from 1 second to a maximum of 18 hours, 12 minutes, and 15 seconds. 8. Choose when to start logging: • Now. Logging begins immediately. • At Interval.
PAGE 5
HOBO Occupancy/Light Data Logger (UX90-005x/-006x) Manual 1. Locate the notch in the upper left corner next to the mounting magnet. Notch on back of logger 2. Insert the black base of the attachment into the notch so that the base clips onto the corner of the logger as shown below. Time Between Events Approximate Total Data Points Approximate Logging Duration (1 Year Battery Life) 16 seconds to 4.25 minutes 63,488 11.76 to 187.38 days UX90-005/ -006 260,096 48.17 days to 2.
PAGE 6
HOBO Occupancy/Light Data Logger (UX90-005x/-006x) Manual 3. Click Save. Note that the selections will not take effect in the logger until you launch it. Reading Out the Logger There are two options for reading out the logger: connect it to the computer with a USB cable and read out it with HOBOware, or connect it to a HOBO U-Shuttle (U-DT-1, firmware version 1.15m030 or higher) and then offload the data files from the U-Shuttle to HOBOware. Refer to the HOBOware Help for details.
PAGE 7
HOBO Occupancy/Light Data Logger (UX90-005x/-006x) Manual Protecting the logger The logger is designed for indoor use and can be permanently damaged by corrosion if it gets wet. Protect it from condensation. If the message FAIL CLK appears on the LCD screen, there was a failure with the internal logger clock possibly due to condensation. Remove the battery immediately and dry the circuit board. Note: Static electricity may cause the logger to stop logging.