User's Manual

EN
6
®
Sport Cub S 2
IMPORTANT: The installed receiver has been pro-
grammed for operation speci cally in this aircraft.
To operate the SAFE system in this aircraft, set up
your optional DSM2/DSMX transmitter using the
chart below.
• SAFE Flight mode is selected using Channel 5
signal (high, middle, low)
• Panic Recovery mode is selected with Channel
6 signal (high, low)
IMPORTANT: A transmitter with a 2-position
Channel 5 switch will only allow the use of
position 0 or position 2  ight modes. If possible
assign Channel 5 in your transmitter to a
3-position switch to operate all 3  ight modes
(refer to your transmitter manual).
Refer to your transmitter’s manual for more information about transmitter setup.
Non Computerized Transmitter Setup
(DX4e and DX5e)
Transmitter
SAFE
Mode
Switch
Panic
Recovery
Switch
SAFE
Flight
Modes
Supported
Throttle, Aileron, Elevator and Rudder in Normal Position
DX4e
(2pos switch)
ACT/AUX
switch
Trainer Button
2 Pos
Flight Mode
DX4e
(3pos switch)
CH 5
switch
Trainer Button
3 Pos
Flight Mode
DX5e
(2pos switch)
CH 5
switch
Trainer Switch
2 Pos
Flight Mode
DX5e
(3pos switch)
CH 5
switch
Trainer Switch
3 Pos
Flight Mode
Computerized Transmitter Setup (DX6i, DX6, DX7S, DX8, DX9, DX10t and DX18)
Start all transmitter programming with a blank model (do a model reset), then name the model.
Set Dual Rates to:
HIGH 100%
LOW 70%
DX6i
1. Go to the SETUP LIST MENU
2. Set MODELTYPE: ACRO
3. Set REVERSE: Gear Channel
4. Go to ADJUST LIST MENU
5. Set TRAVEL ADJ: Gear/Fmode (0)100%; Gear/Fmode (1) 40%
6. Set FLAPS: Norm 100; LAND 100
7. Set MIX 1: ACT; Gear Gear ACT, RATE D 0%; U + 100%, SW MIX, TRIM INH
Resulting
in:
The Gear and Mix switches operate the 3 SAFE modes
Gear 0; Mix 0 = Beginner Mode
Gear 1; Mix 0 = Intermediate Mode
Gear 1; Mix 1 = Experienced Mode
The Flap switch operates Panic Recovery.
Position 0, Panic Recovery off, Position 1 Panic Recovery on
DX7S
DX8
1. Go to the SYSTEM SETUP
2. Set MODEL TYPE: AIRPLANE
3. Set SWITCH SELECT: Change all to INH then TRAINER: AUX1, FLAP: GEAR
4. Go to the FUNCTION LIST
5. Set SERVO SETUP: Reverse AUX1
Resulting
in:
Flap/Gyro Switch operates the 3 SAFE modes (0 Beginner/1 Intermediate/
2 Experienced) The Trainer/Bind button operates Panic Recovery
DX6
DX9
DX10t
DX18
1. Go to the SYSTEM SETUP
2. Set MODEL TYPE: AIRPLANE
3. Go to CHANNEL ASSIGN: click NEXT to go to Channel Input Con g: Set GEAR: D
(DX10t: GEAR: A) Set AUX1: i (DX10t: AUX1: R-tip)
4. Go to the FUNCTION LIST
5. Set SERVO SETUP: Reverse AUX1
Resulting
in:
Switch D (DX10t: A) operates the 3 SAFE modes (0 beginner/1 intermediate/
2 Experienced) The Bind/I button (DX10t: R-tip) operates Panic Recovery
Transmitter Setup