Before operating this unit, please read these Instructions completely. ALMOST UNBREAKABLE Mitts -EPF INSTRUCTIONS Features: Pitts Special is super aerobatic model for 3D aerobatic flying. Model is produced by modern technology on CNC machines from EPP “almost unbreakable” material. The flying time of Pitts Special is between 8 to 15 minutes, it depends on the flying figures.
[Pupae Do not fly under the conditions below Wind strong enough to make the trees rustle Street with many trees or street lamps Loss to high voltage electrical wires High Population density areas Cautions for flying Large gyms, front lawns and parks make excellent flying areas. Make sure you have permission to fly and follow safety guidelines set by local authorities.
1.Cut a straight slot on the fuselage to 580mm by knife as picture shown. The slot must be 3mm deep and ensure the 1.5mm glass fiber rod inset. 2.Cut a glass fiber rod (Dia 1.6mm) fo the length of 580mm..press. thread Into tha slot which was cut last step. 3.0n the flat board glue the carbon rod into fuselage using CA glue. 4 .Glue the motor mount as shown .use Glucagon. Lai] 5. Insart motor mount into the fuselage .use CA glue. motor Into the motor mount , using PCs screws. =o a 7.Cut opening for ESC .
9 Insert the servos Into the hole as shown .use CA glue . 14.Press the tube into the slot in fuselage as shown glue it using CA lue . 10.Install the push rod connector to the servo arm, insert the quick lock onto the push rod connector . 11.Use your radio system and determine which hole in the servo arms will give the desired control throw. Install the servo arms on the servos. 15.In the same manner install the tube into the right side of fuselage . 12.
17.The stabilizer into the fuselage glue around the edge with CA glue. check the perpendicularity as shown. 18.Using the sharp knife cut the slots for control hom (elevator). 19. Connact the Z wire to the horn (with slot) for elevator push rod , and ensure the wire through the tube in the fuselage .Press the horn Into the slot for the elevator, using CA glue. 20 The Z wire mm Insert Into the push rod connector on the horn of servo for elevator . 21.Glue vertical fin on the fuselage using CA glue .
25.Switch on the RC set. put the control surfaces to the neutral hy . Tighten the connector screws. 28.Put the rule on the lower wing left and right as shown . Cut the slot In the lower side of the lower wing using sharp knife . Cut the excess push rod as shown . The slot must be 3mm deep and 640mm length Press the 640mm glass flier red Into the slot of the wing . 29.0n the flat board glue the glass fiber rod into bottom side of the lower wing using CA glue and apply activator spray. 26.
31.Insert connectors Intel extension of the servo hom . 32.E aileron control arm 1.6mm PCs Install the push rod connector to the aileron horns . 33.Clue the control arms into the 34. Ingert wing left and right into the fuselage as shown .check If the wing Is In the canter and alignment . Also check if the perpendicular to the fuselage si 35, g inp g Apply some glue on the top and glue. the bottom (as shown) 36. Cuta 8mm deep hole on the lower wing for aileron servo. 37.
39.Glue the control horns into the ailerons with CA glue as shown . 40 Insert the control wire into the ailerons ohms and into coronal servo arms as shown . Switch on the re-system to have the servo in neutral . Put the ailerons In neutral . Now the push rod connectors screws must be tightened. 41.Insert the receiver into right place . The fuselage foam well hold It In place .plug the elevator (rudder and aileron servos and ESC connectors into receiver. 42.Insert the brainchild into the fuselage as shown .
47.Glue the control arms Into the ailerons using CA glue . ix the rod junction some Callus 49. Install the wing brace glass fiber rod as picture shown 52.Hollow out the canopy with sharp knife and make enough space for servo arm working 53.Fix the end of PVC without hole to the front of the canopy with glues. 50.
54 Install the canopy to the fuselage with screw and connector 55.Fix the wheel with wheel adapters. A 56.Insert the landing gear into the fuselage. Fix the whi covers with some CA glue. 57.Insert the end of tha Z wire Into the ailerons control horns In the upper wing . Insert the other end of Z wire into the push rod connectors in the lower wing. 58.Install the the propeller and spinner to the motor tighten property. 59.Moving the acct pack make the model balance .
