manual

Manual of QUIK Series Sensorless Brushless Motor Speed Controller
3
3.Set item value
After entering the item, you will hear several tones and green led flash in loop, Set the value matching to a tone by press the “SET” KEY within 2 second when
you hear the tone, then you will hear special tone like ♪ 5 6 5 6”. It means the value is set and saved.
Hold the SET KEY for 3 second, you will go back to step 2. if release the SET KEY within 2 second, you will exit the program mode quickly.
Tone
Items
beeb-,1 tone
green led flash
1 short times
beeb-beeb-,2 tone
green led flash
2 short times
beeb-..,3 tone
green led flash
3 short times
beeb-…,4 tone
green led flash
4 short times
beeb-----,1 long
tone green led
flash 1 long times
beeb-…..,N tone
green led flash
N times
1. Brake Force
50% 75%
100%
2. Drag Brake 0
5% 10% 15% 20%
3. Run Mode
ONE TWO
TWO2
4. Start Force
10% 15%
20%
23% 25%
5.Li-xx Cells Number Auto detect
2 cells 3 cells 4cells 5 cells N cells
6.Cutoff threshold
2.5V
2.8V
3.1V
7. Timing
Low
Mid
High Highest
8.Neutral Range
6 8 10
9.Initial Brake Force
5 10 20 30
10.Reverse Force
25 50 75 100
1.Enter program mode
1 Turn off the ESC, Switch on transmitter, keep throttle stick to the neutral
position
2 Press and hold the “SET” KEY, Switch on the ESC
3 Wait for 3 seconds, special tone like “♪ i3i3” should be emitted ,which
means program mode is entered
2.Select programmable items
After entering program mode , hold the “SET” KEY continuously, you will hear 11 tones and red led flash in a loop in the
following sequence. If you release the “SET” KEY within 2 seconds after one kind of tone, this item will be selected, and enter step 3
beeb- (1 short tone, red led flash 1 short times) Brake Force
beeb- beeb- (2 short tone, red led flash 2 short times) Drag Brake
beeb- beeb- beeb- (3 short tone, red led flash 3 short times) Run Mode
beeb- beeb- beeb- beeb- (4 short tone, red led flash 4 short times) Start Force
beeb----- (1 long tone, red led flash 1 long times) Li-xx cells
beeb----- beeb- (1 long 1 short tone, red led flash 1 long times and 1 short times) Cutoff threshold
beeb----- beeb- beeb- (1long 2 short tone, red led flash 1 long times and 2 short times) Timing
beeb----- beeb- beeb- beeb- (1 long 3 short tone, red led flash 1 long times and 3 short times) Neutral Range
beeb----- beeb- beeb- beeb- beeb- (1 long 4 short tone, red led flash 1 long times and 4 short times) Initial Brake Force
(10) beeb----- beeb----- (2 long tone, red led flash 2 long times) Reverse Force
(11) beeb----- beeb----- beeb-----” (3 long stone, red led flash 3 long times) Restore all to default and Exit
Note: 1 long “beeb-----” = 5 short “beeb-”, flash 1 long times=5 short times
4.Exit program
There are two ways to exit program mode:
1 In step 2, after 3 long tone (The item #11) please release
the KEY within 2 seconds.
2 In step 3,after special tone ♪ 5 6 5 6 , please release the
KEY within 2 seconds.