User Manual

Mx series RX user's manual
For Mx-0104ARX-HBL, Mx-0104ARX-H, Mx-0104ARX-LBL, Mx-0104ARX-L, Mx-0104ARX-LS.
 Mx serie s product s are a g rou p of programmable receiv er t hat integ rates b rush ESC (or brus hless ES C) a nd t wo li ne ar
servos, through elaborate design, it has tiny volume and very light weight, applicable to micro airplanes in any shape;
 This series receiver includes type H and L, type H is a little wider, applicable to various micro 3D airplane, park airplane
and indoor airplane, it can be used on micro triangle airplane through programming, type L is slender, however small your
lover is, it can be matched perfectly;
 To make you use it more conveniently, the ESC type, linear servo control channels and output channels on the receiver
can be programmed easily.
A、Product specification
Type Mx-0104ARX-HBL Mx-0104ARX-H Mx-0104ARX-LBL Mx-0104ARX-L Mx-0104ARX-LS
Number of channels 5CH 5CH 5CH 5CH 3CH
Band 2.4G 2.4G 2.4G 2.4G 2.4G
Internal ESC 3.5A Brushed ESC 2A Brushed ESC 3.5A BL ESC 2A Brushed ESC 2A Brushed ESC
External ESC Unsupported Support Unsupported Support Support
Servo travelling range
8mm 8mm 8mm 8mm 8mm
Servo speed 0.12s/4.2V 0.12s/4.2V 0.12s/4.2V 0.12s/4.2V 0.12s/4.2V
Torque 35g/4.2V 35g/4.2V 35g/4.2V 35g/4.2V 35g/4.2V
Voltage Range 3.0V~4.2V 3.0V~4.2V 3.0V~4.2V 3.0V~4.2V 3.0V~4.2V
Size / mm 32.6x24.5x7.8 25.0x24.5x7.8 55.0x18.1x7.8 45.0x18.1x7.8 45.0x13.0x7.8
Weight 3.1g 2.8g 2.9g 2.7g 2.5g
Antenna Length 30mm 30mm 30mm 30mm 30mm
Programming function
B、C、D、E A、B、C、D、E B、C、D、E A、B、C、D、E A、B、C
Note: Please refer to “Programming fu nction” for the instr uction of programming fu nction.
B、Instructions
1、Connect the motor:
 Mx-0104ARX-HBL, Mx-0104ARX-LBL have internal 3.5A ESC for brushless motor, brushless motor directly connect to
the CON1;
 Mx-0104ARX-H, Mx-0104ARX-L, Mx-0104ARX-LS have internal 2A brush ESC, and support external ESC;
 When connecting a brush motor, before binding, you need to set the SW1 on the module to ON; for the external ESC, you
need t o set t he SW 1 on th e m odul e t o OFF;
 When using internal ESC for brush motor, it’ s in locked state after powered for security reasons, Only when pushing the
throttle stick to its lowest setting (Enable the throttle reverse function, and set the throttle trim switch to the lowest), and stay
about 1 seco nd, whe n L ED on th e rec eiv er is in dark f or 1s, it shows i t has bee n unloc ke d, th en yo u can c ontr ol it ;
 Please see the addendum for the wiring diagram for brush motor and brushless motor.
2、Connecting the servo:
 This series receiver contains two digital linear servos, if you need external servo (unsuitable for Mx-0104ARX-LS), we
rec omm end th at y ou us e digi tal l ine ar se rv o Mi- LSM 130 0;