INSTRUCTION MANUAL +se With Replacement Parts MODELS 8181 & 84181 FOOD CUTTERS {INCLUDES MOTOR PARTS) 116926 — 8181 ML-16927 — B181-D {Without Gear Attach.} ML-16928 ~ 84181 ML-16628 ~ 84181.D {With Gear Attach.) A product of HOBART CORPORATION TROY, OH!O 45374 " FORM 68721 (Rev.
8181 INSTRUCTIONS Instructions for Operation and Care of MODELS 8181 and 84181 FOOD CUTTERS HOBART v D rued) MODEL Serine Fig. 1 INSTALLATION: A.1 Before making any electrical connections, CHECK. THE SPECIFICATIONS ON THE NAME PLATE (1, Fig. 1) TO MAKE SURE THEY AGREE WITH THOSE OF YOUR ELECTRICAL SERVICE. Connect multi phase motors so bow! will turn clockwise (see arrow) (3, Fig. 2). Knives will then turn downward (viewed from the front of the machine). (See arrow on knife shaft (3, Fig. 6)).
Fig. 3 B.4 The shape of the food cutter bowl cover rolls or turns the material. This provides mixing action. It is NEVER necessary to reach beneath the bowl cover. Material can be discharged while the machine is in operation. Should inspection be necessary ALWAYS shut off the motor — wait for the knives to stop. Then unlock and lift the bowl cover to remove any obstruction. B.
8157 INSTRUCTIONS Fig. § C.3 Knives should be sharp, but should not have a razor edge. An extremely thin edge dulls quicker than the sturdy bevel that knives have, when received from the factory.
C.6 ca Fig. 7 ATTACHMENT DRIVE: C.6.1 The attachment drive is for a 412 attachment. Various #12 attachments may be driven by this food cutter. The Chopping End, 9" Vegetable Slicer and the Nicer are the most popular attachments. A Speed Drive attachment which would triple the speed of the 9” Slicer is also available (cannot be used with chopper or cider attachment). C.6.
8181 INSTRUCTIONS .9.1.2.4 The lubricant should be at the gasket line, where the lower gear case cover attaches to the gear case. Note: No lubricant is used in this cavity on machines without the attachment drive. Use “Geared 4657 (Standard Oil Co., Ohio} or medium weight transmission oil with a Say bolt viscosity 210° F. if additional lubricant is needed. Fig. 9 C.9.1.2 To check the attachment drive gear gasses! Turn off the power supply. C.9.1.2.2 Remove thumb screw and withdraw hub cover (1, Fig. 10} .2.
REPLACEMENT PARTS 8181 ILLUS. PL16723 PART NO. C-119858-2 5-9-49 D-114379.2 5-60-68 ES-16-24 M78732-4 M-8036% B-104725 SD-15-3 WE-15 M-82258 D70487-6 P-65477-53-1 P-65477-53-2 P-65477-53-3 P-65477-53-4 P-63477-53-5 P-65478-56-2 P-65478-56-4 M-79118 B-22275-182 P-22275-183 C-15747-275 D-114379-4 BB-5-30 MOTOR UNIT NAME OF PART Switch Starting (Stationary Part) . . Mach. Resew $6-32 x 3/8" Rd. Hd . Bracket Bearing (Fan End) Bracket Bearing {Fan End) Fan Ventilating 492 7660/ |, Loading Spring N.D. #5817 . . .
8181 REPLACEMENT PARTS G HUNG INGE P USE With FLAT END FANG PIN BOWL UNIT i
REPLACEMENT PARTS 8181 ILLUS, PART PL-16726 NO.
