INSTRUCTION MANUAL .« . with Catalog of Replacement Parts HOBART MODEL 411 MEAT SLICER Spec. #4823 The Word’s Oldest and f f Computing Scene HOBART/] ™, o ere, Inchon, Bekesy and Dish washing Mac hings THE HOBART MANUFACTURING COMPANY TROY, OHIO FORM 6178-F {Revised Sept.
411 INSTRUCTIONS Instructions for Operation and Care of Hobart Slicer Model 411 FlG. 1 . ELECTRICAL CONNECTIONS: Check the electrical specifications for the motor, which ave stamped on the name plate under the slice adjusting lever (1) Fig. 1, before connecting to the power supply. . SAFETY PRECAUTION: When the Slicer is not in use, keep the slice adjusting lever (1) on zero. This guards the knife, . THICKNESS OF SLICES: Movement of the lever (1) adjusts the slice thickness.
8 Always keep yer hand to the right of this guard (9) ag a safety precaution, CLEANING: Use normal cleaning methods that would be employed on similar equipment. Set the slier adjusting lever (1) at zero and clean the knife while in motion. If a guard is removed for cleaning, exposing the edge of the knife, stop knife and use canton in cleaning. LUBRICATION: Using s small amount of ofl, lubricate the slide rods weekly through the ogler (10) Fig. 1.
ILLUS. PL.3653 1 PART NG, V-13278 48814 Wire-48 CH-86-30 $C-48-9 P-33263 P-12281 5-18-12 5-11-13 R-13264 R-13205 P-85108 ES-8-1 W42 V13186 WE-4-18 R-13287 M-80288 5-36-32 T-15305-2 P-11800-157 SC-39-15 Ward-2 SC-54 P-11800-116 5-13285 M-15888 NS-17-7 V140511 V-14051-2 M-14048-1, M-14048-8 8-63335-7 8-63335-17 5-68835-30 B-63335-43 M-14050-2 P-23415 REPLACEMENT PARTS BASE AND MAIN FRAME UNIT NAME OF PART AMT. Spring 1 Mach, Nut Square .. 1 Lock Washer 5/16” x 143" X . 1 Fin.
411 REPLACEMENT PARTS PL~987] CARRIAGE UNIT ILLUS. PART OLES? NO. NAME OF PART AMT. 1 NEAT Jam Nut Hex Fin, Mach. Resew V-22163 Screw Special Knurled Hd. 2 4 Tray Carriage 1 5 SC-8-11 Mach, Screw WISE-22 Lock Washer #10 x .055" x .040” 1 7 R-13801 Grip Meat 1 8 O-2-5 Key #405 Wood ruff 1 g ES-8-24 Washer (1/16” Thi) 45 Reed, 16 WE-g-28 Washer (1/327 Th) . -As Reed. 1 8018 Mach.
ILLUS, PART FL-1317 NO. 1 R-12430-47 3 V16583 3 4 ES-11-20 5 6 AT 7 ATy 8 V179781 9 V177782 16 R-12430-8 1 R-13286 2 R-18238 12 V13177 14 N-52-29 1% M-12743-2 16 WSW 1 P-12170 18 502239 1 £-13283 REPLACEMENT PARTS PL~1317 KNIFE, GEAR, AND GUARD UNIT NAME OF PART Key Spring Knife Shaft Roller Bearing Cup & Cone Ayes. Washer THRUST emote, Stop Nut “Flexible” Retainer Shock Washer (20/64” L D3 Retainer Shock Washer (41/647 L D) Shock Washer (28/64” 1 DJ . Heck Washer (41/647 1 D.) . Center Plate & Knob Says.
411 REPLACEMENT PARTS GRINDER UNIT ILLUS. PART PL-GS NO. NAME OF PART AMT. 1 H-13208-2 Pedestal Grinder Housing e 1 2 SC-15-70 Mach, Resew 17420 x 17 Oval Hd 2 3 M-22184 Resew Knurled Thumb z 4 V-13186-2 Knob Pull Rod .. i 5 P-13224 Guide Wheel Carrier 1 8 V18188 Bushing 1 7 M-18220-§ Nut Thumb 1 8 5430022 Housing Grinder 1 9 WS3-11 Washer ..
