UNCATALOGUED OF REPLACEMENT PAR.TS WITH INSTRUCTIONS FOR OPERATION AND CARE OF: : : Model . No. 110 & Model . . No. 210 MEAT SLICERS THE HOBART MANUFACTURING CO. TROY, OHIO, U.S. A.
HOBART REPLACEMENT PARTS Instructions For Hobart Slicer Model 110 and Model 210 1—INSTALLATION See that the four rubber feet {A) are in place. They are packed in a small cloth bag that is included with the shipment, and they may be inserted by twisting to the right, just as though they were screws. For installation on shipboard -omit the rubber feet and secure the machine to the table with 4" ——13 cap screws.
HOBART REPLACEMENT PARTS 3 —REMOVING CARRIAGE Loosen the thumb screw C, and lifting the carriage straight up, remove it from the machine. When is done a smooth working table is exposed which facilitates DE-crusting loaves of bread, and DE-rinding slabs of bacon. 4 -~ CLEANING Wipe off the surface of the machine daily with a cloth wrung out in warm water, Once a week, saturate 2 bit of cloth with the tasteless il that is [burnished and rub over the entire machine.
HOBART REPLACEMENT PARTS () Adjusting Slice Deflector Clearance The slice deflector should come within a thirty-second of an inch from the back of the knife. If it does not, adjustment can be made by turning the slotted head of the stop screw that lies behind the deflector. {D) To Adjust for Wear of the Knife Repeated sharpening will wear down the diameter of the knife and as the diameter becomes less three adjustments will be needed. 1—Move the Gage plate over nearer to the knife.
HOBART REPLACEMENT PARTS moss B 7 522 =l o 50963 } | 54680 / 3856 y 3e8z aeg \3883 ?884 13857 52303 13861 7 Pl-deg Parts for Knife, Gears and Guards Unit 13 850 Knife — For 116 & 210, 1385 Adjust ooy Ny oAb & Rile Guard — Bor 10 & 210 13 854 13 855 Kn per Knife Guard — For 110 & 2 13 336 Knife Shaft — For 116 & 2. 13 857 Rear Unite Guard £3 858 Kline Shaft. Coleys — For 110 & 210 ‘yetis — For 13859 Spiral Gear, 13 860 Retaining Nut 863 Halt me on.
HOBART REPLACEMENT PARTS assn/ 8335|/ ;33“ Catalog PART NAME No. Factory No. Rea. No.
G5 Spring for Carriage Han die — Yor 110 & 2] HOBART REPLACEMENT PARTS e WM CT-56367 {17708 770 Parts for Carriage Unit Model 110 and Model 210 (Specification 3441 and Later) PART NAME No. Factory Code Req. ¢ Meat Get aad Shay — For 119 & 210. Carriage Handle — For 110 & 2 She sor Carving Handle = Fo Fiber Washer, large siege, 1/167 chit, —~ For Fiber Washer, Laze site, 132" thi ik Elbe Washer, Small Size, 1,320 Chic.
HOBART REPLACEMENT PARTS DB-110 Motor and DB-210 Motor For Model 110 and Model 210 Gallon PART NAME No. 12490 Fed Assembly Complete (State Voltage) 158 Mr Ea Sliakepsaol Dishwasher 19453 Armature Assembly (compete (State Vot 19 494 Brush Holder. 19497 Eating Tracker. 498 Ball Bearing N.D. 499 i 1 M17000-7-8 Doom 19 500 3 Sepia Dowry 19 501 i 19 502 i io 503 1 19 501 s0s 1 19 507 3 19 508 1 19 509 i Isidro Don 19 510 i Dons Commercial Stock Can log PART NAME Material No. Cod N, Red, Word 51 328 No.
HOBART REPLACEMENT PARTS Model 110 and Model Catalog 009 148 207 288 304 363 439 733 059 963 965 253 320 367 349 565 45 56 442 Commercial Stock for Description Mariner No. 440 x X" Round Head Machine Strew.. Plated No. 832 x 34" Round Head Machine Screw.. . Sl o, 10-24 x §/16” Round Head Marine Screw... Eli. Tia No. 12-24 x 3" Round Head Machine Screw. Skeet No. 12-24 5 17 Gourd Head Machine Screw.. Stet W20 x 35" Round Head Machine Sore. Eli. Tin 571618 % 14" Round Head Machine Screw.. Eli. Tin No.
