Manual

ManualsBrandsHMC Electronics ManualsPower ToolsPLUTO10D Kolver PLUTO DC Controlled Electric Torque Screwdriver

DECLARATION OF CONFORMITY

KOLVER S.r.l.

Via Marco Corner, 19/21

36016 THIENE (VI) ITALIA

Declare that the new tool here described:

Electric screwdriver:

PLUTO10P/N 130210/N  PLUTO10P/U/N 130215/U/N 

PLUTO15P/N 130215/N  PLUTO15P/U/N 130215/U/N 

PLUTO10D/N 130211/N  PLUTO15D/N 130216/N 

PLUTO3D 130203  PLUTO3P 130204 

Is in conformity with the following standards and other normative

documents :

98/37/CE, 89/336/CE and 2006/95/CE,

EN 50144-1 and EN 602004-1

It is also in conformity with RoHS normative.

Name: Giovanni Colasante

Position: Managing Director

Giovanni Colasante

KOLVER S.r.l.

Documentation Provided By HMC Electronics

33 Springdale Ave. Canton, MA 02021

http://www.hmcelectronics.com

(800) 482-4440

Summary of content (6 pages)

PAGE 1
DECLARATION OF CONFORMITY KOLVER S.r.l. Via Marco Corner, 19/21 36016 THIENE (VI) ITALIA Declare that the new tool here described: Electric screwdriver: PLUTO10P/N 130210/N PLUTO15P/N 130215/N PLUTO10D/N 130211/N PLUTO3D 130203 PLUTO10P/U/N 130215/U/N PLUTO15P/U/N 130215/U/N PLUTO15D/N 130216/N PLUTO3P 130204 Is in conformity with the following standards and other normative documents : 98/37/CE, 89/336/CE and 2006/95/CE, EN 50144-1 and EN 602004-1 It is also in conformity with RoHS normative.
PAGE 2
Operator’s Handbook IDENTIFICATION DATA OF THE MANUFACTURER KOLVER S.r.l. VIA MARCO CORNER, 19/21 36016 THIENE (VI) ITALIA IDENTIFICATION DATA OF THE PRODUCT PLUTO10P/N 130210/N PLUTO15P/N 130215/N PLUTO10D/N 130211/N PLUTO3D 130203 PLUTO10P/U/N 130215/U/N PLUTO15P/U/N 130215/U/N PLUTO15D/N 130216/N PLUTO3P 130204 THECNICAL DATA OF THE PRODUCT TENSION: 40V DC POWER: 90W MAX SPEED RPM: PLUTO 10:600; PLUTO 15:320; PLUTO3: 1200 TORQUE RANGE Nm: PLUTO10:0.6 - 10; PLUTO15:0.6 - 15. PLUTO3:0.3 - 3.
PAGE 3
GENERAL SAFETY RULES WARNING: when using electric screwdrivers, basic safety precaution should always be followed to reduce the risk of fire, electric shock and personal injury. Read all the instructions below before using the screwdriver and save them. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. Keep the work area clean and well lit. Do not use the electric screwdrivers in dampt or wet locations or in presence of flammable liquid or gases.
PAGE 4
1. Applications KOLVER electric screwdrivers are used to tighten to the required torque screws, nuts, studs and any other kind of threaded connection on any material. Table 1 will show you the capacity and the torque range of this screwdriver. Obviously, it is possible to use the screwdrivers with screws having a larger diameter if the torque falls within the indicated range. All models are reversible and can consequently be used to unscrew.
PAGE 5
3. Power supply and torque control unit EDU1AE power supply and control units act as voltage transformer and electronic torque controller. The power supply 230V-50Hz AC is converted into 40V DC required by PLUTO series screwdrivers through a transformer certified EN61558-1/p2-6. The electronic control circuit cuts the power supply to the motor calculating the correct torque in response to 3 parameters, voltage frequency and current, according to the selected options.
PAGE 6
For on line or laboratory calibration of the screwdriver torque output we recommend the use of either K20 torque analyzer with internal and external transducer. 5. Maintenance The screwdriver’s motor is maintenance free. NOTE The sound level generated by Kolver electric screwdrivers is always lower than 70dB(A). The vibrations transmitted to operator’s hand are lower than 2.5m/s². In particular the exposition to vibrations is lower than 1m/s² for operators who make up to 4200 screwing cycles per day.