Instruction Manual

ManualsBrandsHMC Electronics ManualsPower ToolsESL324P-ESD Delta Regis Electric Screwdriver, Push Start

32V DC

Electric Screwdrivers

Operating Instructions

For use with the following lever start models:

ESL310-ESD; ESL310S-ESD; ESL311-ESD; ESL312-ESD; ESL323-ESD;

ESL324-ESD; ESL327-ESD; ESL328-ESD; ESL329-ESD

For use with the following push start models:

ESL323P-ESD; ESL324P-ESD; ESL327P-ESD; ESL328P-ESD; ESL329P-ESD

Documentation Provided By HMC Electronics

33 Springdale Ave. Canton, MA 02021

http://www.hmcelectronics.com

(800) 482-4440

Summary of content (5 pages)

PAGE 1
32V DC Electric Screwdrivers Operating Instructions For use with the following lever start models: ESL310-ESD; ESL310S-ESD; ESL311-ESD; ESL312-ESD; ESL323-ESD; ESL324-ESD; ESL327-ESD; ESL328-ESD; ESL329-ESD For use with the following push start models: ESL323P-ESD; ESL324P-ESD; ESL327P-ESD; ESL328P-ESD; ESL329P-ESD Documentation Provided By HMC Electronics 33 Springdale Ave. Canton, MA 02021 http://www.hmcelectronics.
PAGE 2
WARNING READ AND UNDERSTAND ALL INSTRUCTIONS Disconnect the controller power cord from the receptacle before performing any maintenance on this tool. Do not attempt to repair this tool unless you are a qualiﬁed technician. When using electric tools, basic safety precautions should always be followed to reduce the risk of ﬁre, electric shock and personal injury. Read all instructions before using the tool. Be sure to save this manual for future reference. IMPORTANT SAFETY INSTRUCTIONS 1.
PAGE 3
4. Tool Use and Care 4-1 Use clamps or other practical means to secure and support the workpiece to a stable platform. Holding the work by hand or against your body is unstable and may lead to loss of control. 4-2 Do not force tool. Use the correct tool for your application. The correct tool will do the job better and safer at the rate for which it is designed. 4-3 Do not use the tool if the switch does not turn it on or oﬀ.
PAGE 4
Speciﬁcations Torque Speed (RPM)* in-lb Nm kgf-cm Hi (32V) Lo (20V) Weight (gr) Length (mm) ESL310-ESD 0.2 – 3.1 0.02 – 0.34 0.2 – 3.5 1000 600 270 205 ESL310S-ESD 0.2 – 3.1 0.02 – 0.34 0.2 – 3.5 500 350 270 205 ESL311-ESD 0.4 – 6.2 0.05 – 0.69 0.5 – 7 1000 600 270 205 ESL312-ESD 0.9 – 8.8 0.10 – 0.98 1 – 10 670 400 270 205 ESL323-ESD 1.5 – 10.6 0.17 – 1.2 1.7 – 12 1000 600 480 230 ESL324-ESD 3.0 – 14 0.34 – 1.58 3.
PAGE 5
Torque Adjusting Nut Turn to adjust torque. Higher values on scale indicate higher torque. Numbers on the scale are for reference only and are not a torque indication. Externally Replaceable Brushes Remove caps to replace brushes. Ensure the curved edge of the brush aligns with the curve of the commutator. DO NOT OVER TIGHTEN CAPS! Trigger Suspension Ring Use to suspend the tool. Bit Holder Retract sleeve to insert/remove bits. Housing Nut Remove housing nut to install torque locking sleeve.