User's Manual
Table Of Contents
- Document Reference
- 1 Important Safety instructions
- 2 Introduction to FreeSpeak II™
- 3 Installing a system
- 4 Connecting the Base station
- 4.1 Understanding the Back-Panel Connectors
- 4.2 Connecting to partyline intercom systems
- 4.3 Wireless partyline
- 4.4 Connecting to 4-Wire and digital matrix intercom
- 4.5 Connecting to a program audio source
- 4.6 IFB configuration
- 4.7 Connecting to the stage announce output
- 4.8 Connecting to a PC
- 4.9 Connecting to transceiver/antennas
- 5 Operating the Base station
- 6 Programming a system from the Base station
- 6.1 Introduction
- 6.2 Using the Base station’s programming menus
- 6.3 Saving changes
- 6.4 Changing beltpack labels
- 6.5 Setting and changing port labels
- 6.6 Setting and changing group labels
- 6.7 Adding group members
- 6.8 Beltpacks
- 6.9 Assigning audio routes to a beltpack
- 6.10 Setting the beltpack audio level
- 6.11 Setting beltpack latching
- 6.12 Over the Air (OTA) beltpack registration from the Base station
- 6.13 Setting input and output port levels
- 6.14 Setting port call destination
- 6.15 Configuring a wired partyline
- 6.16 Base station System Menu
- 6.17 System Info
- 6.18 Restoring the Defaults
- 6.19 Antennas
- 6.20 Setting the IP address
- 6.21 Locking front-panel enable buttons
- 6.22 Remote microphone kill
- 6.23 Battery indicator
- 7 Operating the wireless beltpack
- 8 Programming on the beltpack
- 8.1 Introduction to programming on the beltpack
- 8.2 Configuring the beltpack volume settings
- 8.3 Configuring the beltpack headset
- 8.4 Configuring the beltpack microphone
- 8.5 Configuring the beltpack display and LEDs
- 8.6 Configuring the beltpack alarm options
- 8.7 Selecting the beltpack role default set
- 8.8 Selecting the beltpack administration
- 8.9 Setting the listen again option
- 8.10 Accessing beltpack information
- 8.11 Setting display mode
- 8.12 Setting system connect
- 8.13 Enabling over the air (OTA) registration mode from a beltpack
- 8.14 Performing a site survey
- 9 Operating the transceiver/antenna
- 10 FS II Configuration Editor
- 10.1 Loading configurations
- 10.2 Configuration Editor Screen basics
- 10.3 Registering beltpacks using the over the air (OTA) facility
- 10.4 Configuring beltpacks
- 10.4.1 Selecting the beltpack to register or edit
- 10.4.2 Registering beltpacks using the micro USB cable
- 10.4.3 Viewing beltpack registration information
- 10.4.4 Viewing beltpack properties
- 10.4.5 Beltpack audio levels
- 10.4.6 Beltpack alarm options
- 10.4.7 Setting the beltpack role options
- 10.4.8 Assigning beltpack keys
- 10.4.9 Configuring the Reply key
- 10.4.10 Key assignment types
- 10.5 Configuring ports
- 10.6 Configuring groups and wireless partylines
- 10.7 Reducing antenna interference
- 10.8 Configuring IFBs
- 10.9 Configuring Base station system parameters
- 10.10 Diagnostics
- 11 Specifications
- 12 Compliance
9.2.2 PD2203 rear panel
Figure 9-4 FS II Splitter Rear Connector Panel
9.2.2.1 Serial data connector
This 3.5 mm (1/8 inch) tip-ring-sleeve (TRS) connector is used for upgrading the firmware in
the PD2203. It will typically be unused.
9.2.2.2 Power Indicator
This green LED indicates that the splitter is receiving power from the external power supply.
9.2.2.3 DC IN power connector
This connector is used to locally power the antenna splitter with the supplied universal power
supply. Use of local power is required.
9.2.2.4 EXP IN connector
This male DB-15 connector is reserved for future use.
9.2.2.5 EXP OUT connector
This female DB-15 connector is reserved for future use.
9.2.3 Connecting an antenna splitter to the FS II Base station and to
transceiver/antennas
After the connections have been made between the splitter and the transceiver/antennas,
make sure that the data LED’s are lit at the individual ports on the antenna splitter. Also make
sure that the both the green power LED and the yellow data LED are lit on each FS II-TA. If all
are properly lit, then the connection has been successfully made and the coverage zones will
be active and will support beltpacks. If the transceiver antennas are not lit, check the
connections.
94
FreeSpeak II User Guide