User Manual

ManualsBrandsHM Electronics ManualsAudio EquipmentHS400 Headset

Figure 2.

Correct wearing

of headset

base of

microphone

boom

HS400

Headset

OPERATING INSTRUCTIONS

The HS400 Headset is a compact, wireless headset intended for use with the HME Wireless Drive-

Thru Audio System 400. The following instructions provide the proper use and care of the HS400.

I. HS400 HEADSET FEATURES

II. HOW TO WEAR THE HS400 HEADSET

•• Wear microphone on right or left side

•• Wear microphone near side of mouth

•• To adjust microphone position hold microphone

boom at base and pivot boom up or down

HM ELECTRONICS, INC.

14110 Stowe Drive, Poway, CA 92064 USA • Phone: 1-800-848-4468 Fax: (858) 552-

0172

HME# 400511

Rev

2/17/03

Figure 1. Headset features

Summary of content (8 pages)

PAGE 1
HS400 Headset OPERATING INSTRUCTIONS The HS400 Headset is a compact, wireless headset intended for use with the HME Wireless DriveThru Audio System 400. The following instructions provide the proper use and care of the HS400. I. HS400 HEADSET FEATURES Figure 1. II.
PAGE 2
III. ROUTINE HS400 OPERATION HS400 control buttons are touch-sensitive. Use your fingertip, not your fingernail, when touching the buttons. The HS400 can be operated in “half-duplex” or “full-duplex” modes. In the half-duplex mode, you must press and hold a button while talking to a customer, and release the button to hear the customer’s response. The HS400 push-to-talk (PTT) mode is an example of half-duplex operation.
PAGE 3
C. Talk to Customers 1. Single-Lane Operation (one base station operating one speaker post) a. Push-To-Talk Mode • • • Customer begins speaking at speaker post or menu board Adjust customer’s voice level in headset if necessary Press and hold A1 or A2 button to speak to customer — Release to listen b.
PAGE 4
D. Talk to Other Crew Members • • Press and hold B button to speak to other crew members wearing HS400s Release to listen E. Change and Charge Batteries If you hear “Headset Battery Low” in your headset, the battery needs to be replaced and recharged. HS400 batteries need be recharged after 8 to 9 hours of normal use. 1. Change Batteries Battery release button a. Battery Removal • • Press upward on battery-release button Pull battery out from the top Figure 3. Battery removal b.
PAGE 5
IV. AUTO-HANDS-FREE SETTING The auto-hands-free feature allows only one operator to communicate with a customer in one drive-thru lane without pressing any buttons. CAUTION: Only one HS400 per lane can be set in the auto-hands-free mode, or interference will occur when a customer enters the drive-thru lane. • • V.
PAGE 6
C. Channels 0 - 7 CAUTION: The HS400 channel setting should not be changed unless it has been necessary to change the drive-thru audio system base station frequency. Call HME Customer Support at 1-800-848-4468 for assistance.
PAGE 7
VI. WHAT TO DO IN CASE OF PROBLEMS If any problem occurs in operation of your HS400, replace the battery with a known-good battery. If the problem is not corrected, call HME Customer Support at 1-800-848-4468. VII. HOW TO CARE FOR THE EQUIPMENT A. Proper Handling • • • When adjusting microphone position, hold boom at base, not at microphone end. Carry headset by headband, not by earpiece or battery end, and never by microphone boom. Use both hands to put headset on or take it off. B.
PAGE 8
VIII. EQUIPMENT SPECIFICATIONS IX. Battery type: 3.6 Volt Lithium Ion Battery life: 8 hours (typically) RF Frequency: Receive Transmit Weight: 4.7 oz (1.33 kg) with battery Controls: Power ON/OFF button Volume-up button Volume-down button “A1” button “A2” button “B” button Indicators: Dual color LED (red/green) - 457.5125MHz – 457.6125MHz 468.4875MHz – 469.