User's Manual
Table Of Contents
- Document Reference
- 1 Important Safety instructions
- 2 Introduction to FreeSpeak II™
- 3 Installing a system
- 4 Connecting the Base station
- 4.1 Understanding the Back-Panel Connectors
- 4.2 Connecting to partyline intercom systems
- 4.3 Wireless partyline
- 4.4 Connecting to 4-Wire and digital matrix intercom
- 4.5 Connecting to a program audio source
- 4.6 IFB configuration
- 4.7 Connecting to the stage announce output
- 4.8 Connecting to a PC
- 4.9 Connecting to transceiver/antennas
- 5 Operating the Base station
- 6 Programming a system from the Base station
- 6.1 Introduction
- 6.2 Using the Base station’s programming menus
- 6.3 Saving changes
- 6.4 Changing beltpack labels
- 6.5 Setting and changing port labels
- 6.6 Setting and changing group labels
- 6.7 Adding group members
- 6.8 Beltpacks
- 6.9 Assigning audio routes to a beltpack
- 6.10 Setting the beltpack audio level
- 6.11 Setting beltpack latching
- 6.12 Over the Air (OTA) beltpack registration from the Base station
- 6.13 Setting input and output port levels
- 6.14 Setting port call destination
- 6.15 Configuring a wired partyline
- 6.16 Base station System Menu
- 6.17 System Info
- 6.18 Restoring the Defaults
- 6.19 Antennas
- 6.20 Setting the IP address
- 6.21 Locking front-panel enable buttons
- 6.22 Remote microphone kill
- 6.23 Battery indicator
- 7 Operating the wireless beltpack
- 8 Programming on the beltpack
- 8.1 Introduction to programming on the beltpack
- 8.2 Configuring the beltpack volume settings
- 8.3 Configuring the beltpack headset
- 8.4 Configuring the beltpack microphone
- 8.5 Configuring the beltpack display and LEDs
- 8.6 Configuring the beltpack alarm options
- 8.7 Selecting the beltpack role default set
- 8.8 Selecting the beltpack administration
- 8.9 Setting the listen again option
- 8.10 Accessing beltpack information
- 8.11 Setting display mode
- 8.12 Setting system connect
- 8.13 Enabling over the air (OTA) registration mode from a beltpack
- 8.14 Performing a site survey
- 9 Operating the transceiver/antenna
- 10 FS II Configuration Editor
- 10.1 Loading configurations
- 10.2 Configuration Editor Screen basics
- 10.3 Registering beltpacks using the over the air (OTA) facility
- 10.4 Configuring beltpacks
- 10.4.1 Selecting the beltpack to register or edit
- 10.4.2 Registering beltpacks using the micro USB cable
- 10.4.3 Viewing beltpack registration information
- 10.4.4 Viewing beltpack properties
- 10.4.5 Beltpack audio levels
- 10.4.6 Beltpack alarm options
- 10.4.7 Setting the beltpack role options
- 10.4.8 Assigning beltpack keys
- 10.4.9 Configuring the Reply key
- 10.4.10 Key assignment types
- 10.5 Configuring ports
- 10.6 Configuring groups and wireless partylines
- 10.7 Reducing antenna interference
- 10.8 Configuring IFBs
- 10.9 Configuring Base station system parameters
- 10.10 Diagnostics
- 11 Specifications
- 12 Compliance
SW (software)
Version number
Beltpack. ID (beltpack identity) ID number
RFP (Remote Fixed Part – antenna/receiver) ID number
Regional (DECT frequency area) DECT region. For example, US_DECT.
Battery Level
Percentage charge, hours of use
Table 8-1 Beltpack information
8.11 Setting display mode
You can select between two display modes: Intercom mode and Partyline mode.
Note: You can only access this option if you have advanced menu access.
1) To enter the beltpack menu, press and hold the Menu key.
2) Use the rotary and Menu Select keys to select Display Mode.
3) Use either rotary control to select between:
• Intercom mode
• Partyline mode
8.12 Setting system connect
Use this option to connect to an antenna.
1) To enter the beltpack menu, press and hold the Menu key.
2) Use the rotary and Menu Select keys to select System Connect.
A list of available systems appears on the beltpack screen.
3) Use the rotary control to select a system.
8.13 Enabling over the air (OTA) registration mode from a
beltpack
In some circumstances you may need to enable registration of beltpacks without having
access to a Base station or computer. In this case it can be done from a beltpack.
The beltpack needs to be previously registered and connected. You need the system admin
code, available from Eclipse EHX, the Configuration Editor or the Base station. (The default
code is 4632).
Note: The admin code is available on the System tab in the FS II Configuration Editor. On the Base
station go to MENU->SYSTEM->REG->PIN to find this code.
1) From the registered, connected beltpack press and hold the MENU button for 2
seconds to enter the menu options.
87
FreeSpeak II User Guide